Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hai Everybody,
I want to do Digital communication lab experiment (SOURCE ENCODER AND DECODER) using Multisim. So anybody please help me for which type of encoder and decoder can we use.
Thanking You.
With Regards,
Sindhuri.
here is the circuit diagram of continuous balance type dvm
Please, Explain me the working from chopper to servo motor clearly...!
Thanks in advance.
With Regards.
Hai...
I have small doubt in this dvm
Here the question is, in this dvm there is chopper(comparator between dc input voltage and reference voltage) connected to pre-amplifier,power amplifier and servomotor.
the output of the chopper is a square waveform, where the amplitude is the function of...
Good Morning,
I want to know how MOC3021 IC gets triggered in the module designed by sunrom technologies. overview of the module is attached here. Is the data from pins D0-D3 is given to MOC3021 IC or another 4 pin optocoupler presented in the module. Please also tell me what is the use of 4...
Good Evening,
Please anyone can tell me that how we can use only one technology at a time by using a SIM300 GSM/GPRS Tri-band Module as shown in the attached photo.
My question is that at a time we can use either a GSM Technology or GPRS Technology that which is useful to our project...
Good Evening one and all,
I am using a APR9600 Voice Module to give a confirmation feedback of the device operated. The module is shown in the attached photo. In this we have 8 Message pins in those 8 message pins we have record messages such as level 4, level 3, level 2, level 1. My Project is...
Good Morning one and all,
In ARM7 LPC2148 Microcontroller there are two ports: port 0 and port1. In port 0 there are pins from p0.0 to p0.31 and in port 1 there are pins from p1.16 to p1.31.
Now my question is that in port 0, pins p0.24, p0.26 and p0.27 and also in port 1, pins p1.0 to p1.15...
Good Evening one and all,
I want to connect the USB Port of PC to Zigbee module as shown in the attached photos by using a BF810 USB to Serial adapter cable.
The USB of the cable is connected to the USB port of the PC. Aslo tell is there any MAX 232 IC present in the converter that is...
Good Morning one and all,
Is it possible to connect a DB9 Connector at the output of the MAX232 Board. Please any one can help me quickly.
Thanks in Advance.
Good Morning One and All,
I want to use a USB to serial (DB-9) adapter cable of BF-810 to connect a PC to a Zigbee Module.
I want to know that the input data to Zigbee module will be in TTL or RS232 format.
Please any one can help me on this to get a clear idea.
Thanks...
Good Morning one and all,
I want to know is there any Analog to Digital Converter(ADC) presented in this module shown in the figure below.
Thanks in Advance.
You have to used conditions based upon serial command (data) received by ARM7.
if(datareceived = X) then turn ON FAN...
Good Morning sir,
after this process i want to get a confirmation output by voice by using APR9600 voice module then how this data 'X' will process to the voice module. As i...
Good Evening Sir,
I has a small question that is, after ARM7 LPC2148 Microcontroller has received some serial data then how the Microcontroller will came to know to process the data to a particular module to get the output.
That means in the kit we will use different modules for various outputs...
Good afternoon one and all,
I want to know about the processing of ARM7 Microcontroller. I want to operate more than one load connected to the ARM7 LPC2148 Microcontroller. My Project is based on speech recognition technique, and to control the intensity of loads such as fan or light with...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
