Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

orcad problems in layout and shematic

Status
Not open for further replies.

Tom2

Full Member level 5
Joined
Nov 11, 2006
Messages
318
Helped
3
Reputation
6
Reaction score
3
Trophy points
1,298
Activity points
3,457
I did a pcb with orcad and i get the following message:

In layout :
The first time which i try to choose the footprint i did a mistake and after this, each time which i load the netlist.mnl i get the same message. (I tried to recreate a new netlist, i copy the shematic to another project .... but the error is not able to correct).

AutoECO Error Report
FILE-A: C:\ORCAD\ORCAD_16.0\TOOLS\LAYOUT\DATA\_DEFAULT.TCH
FILE-B: C:\ORCAD_DATA\test.MNL
ERROR: Component U2 (with fp SIP/TM/L.200/2_U2) has no pin 3
1 error found


In shematic i have the following warning (in DRC process) i don't know if i must ignore these warning? :


Checking for Unconnected Nets

WARNING [DRC0007] Net has no driving source RB3: SCHEMATIC1, PAGE2 (1.50, 1.80)
WARNING [DRC0007] Net has no driving source RB2: SCHEMATIC1, PAGE2 (5.10, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB3: SCHEMATIC1, PAGE2 (1.50, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB2: SCHEMATIC1, PAGE2 (5.10, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB0: SCHEMATIC1, PAGE1 (2.20, 3.10)
WARNING [DRC0006] Net has fewer than two connections RB2: SCHEMATIC1, PAGE1 (2.20, 3.30)
WARNING [DRC0006] Net has fewer than two connections RB3: SCHEMATIC1, PAGE1 (2.20, 3.40)
WARNING [DRC0006] Net has fewer than two connections RB1: SCHEMATIC1, PAGE1 (2.20, 3.20)
 

Dear Sir,

In ref U2 components don't have pin 3. But in your may connected in pin 3. Check that component connection. Give appropriate footprint.


WARNING [DRC0007] Net has no driving source RB3: SCHEMATIC1, PAGE2 (1.50, 1.80)
WARNING [DRC0007] Net has no driving source RB2: SCHEMATIC1, PAGE2 (5.10, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB3: SCHEMATIC1, PAGE2 (1.50, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB2: SCHEMATIC1, PAGE2 (5.10, 1.80)
WARNING [DRC0006] Net has fewer than two connections RB0: SCHEMATIC1, PAGE1 (2.20, 3.10)
WARNING [DRC0006] Net has fewer than two connections RB2: SCHEMATIC1, PAGE1 (2.20, 3.30)
WARNING [DRC0006] Net has fewer than two connections RB3: SCHEMATIC1, PAGE1 (2.20, 3.40)
WARNING [DRC0006] Net has fewer than two connections RB1: SCHEMATIC1, PAGE1 (2.20, 3.20)

Reason for unconnected net:
*) May connection given by line. Line no meaning in the circuit. use wire for connection
*) May connection not be in the grid.Use grid during working in the schematics.
*) May that component was not having connection. Give the nc connection.
*)
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top