Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

How to get the rise energy and fall energy

Status
Not open for further replies.

red_0220

Junior Member level 1
Joined
Aug 8, 2009
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,431
Hi all,
I plan to calculate a inverter internal power.
I can know the internal energy equation by primepower manual.
(Internal power = rise_energy + fall_energy)
How to know the rise_energy and fall_energy data?
I need to create a cell library.
 

sudheerprasad

Member level 2
Joined
Aug 25, 2009
Messages
45
Helped
2
Reputation
4
Reaction score
1
Trophy points
1,288
Location
india
Activity points
1,676
______ ______
/ \_______/ \
<--------><---------->
calculate vdd*i(vdd) and integrate it over positive cycle of output until the point where it starts falling for rise_energy.
 

    red_0220

    Points: 2
    Helpful Answer Positive Rating

red_0220

Junior Member level 1
Joined
Aug 8, 2009
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,431
sudheerprasad said:
______ ______
/ \_______/ \
<--------><---------->
calculate vdd*i(vdd) and integrate it over positive cycle of output until the point where it starts falling for rise_energy.



Vout __/一一一\_______/一一\__/
...........<-rise->.<-fall->

so vdd*i(vdd) and integrate it over negative cycle of output until the point where it starts rising for fall_energy (no include posedge and negedge)?
 

Kazzam

Member level 5
Joined
Jul 23, 2007
Messages
91
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
1,820
red_0220 said:
Hi all,
I plan to calculate a inverter internal power.
I can know the internal energy equation by primepower manual.
(Internal power = rise_energy + fall_energy)
How to know the rise_energy and fall_energy data?
I need to create a cell library.

hi...
just curious but what is a cell library???
 

servisgaga1

Newbie level 2
Joined
Nov 2, 2009
Messages
2
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,286
I m also interest about that library cell!?
 

sudheerprasad

Member level 2
Joined
Aug 25, 2009
Messages
45
Helped
2
Reputation
4
Reaction score
1
Trophy points
1,288
Location
india
Activity points
1,676
cell library

cell library consists of combinational and sequential cells,like and ,nand ,dff etc,
each cell is characterised and the prop delay,rise/fall times ,power for diiferent i/p slope and o/p caps
are calculated .
cell library is used in synthesis tools like synopsys design compiler where a RTL code is synthesized to gatelevel code verified ,and when placement and routing is done cell libraries are again.
the better the cell library ,the better is the chip regarding area,power,performance.
there fore cell libraries are important and great effort goes to get a good cell library
 

Kazzam

Member level 5
Joined
Jul 23, 2007
Messages
91
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
1,820
Re: cell library

sudheerprasad said:
cell library consists of combinational and sequential cells,like and ,nand ,dff etc,
each cell is characterised and the prop delay,rise/fall times ,power for diiferent i/p slope and o/p caps
are calculated .
cell library is used in synthesis tools like synopsys design compiler where a RTL code is synthesized to gatelevel code verified ,and when placement and routing is done cell libraries are again.
the better the cell library ,the better is the chip regarding area,power,performance.
there fore cell libraries are important and great effort goes to get a good cell library

great information sudheer!!!! thank you very much
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Top