Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
how can i check faulty ignitor of hpsv lamp
Wow...it's was been a long time to get response since i open this "superimposed" topic, ...
So, what is really your problem? please tell me in details,...maybe i can help u..
regards,
Seety
test engineer and product engineer...
Hi all,
i would like to know what the different of the jobs scope between the Test Process and Test Product engineer in semiconductor manufacturing industry?? what the skills are required for both positions.. I really need your help because i will have an...
Hi all,
i would like to know what the different of the jobs scope between the Test Process and Test Product engineer in semiconductor manufacturing industry?? what the skills are required for both positions.. I really need your help because i will have an interviewed for both position. for your...
Hi... here is the VHDL language...
for adder: sum<=a+b;
Multiplexer (4-bit) :
begin
process (sel,a,b)
begin
if (sel='0') then
y <=a;
else
y<=b;
end if;
end process;
end logic;
And i'm not sure for the shift register...but i know the VHDL language for shift and...
measure power losses...
Hiii everybody,
Have anybody here knows the method to measure power losses for High Pressure Sodium Vapor (HPSV) ballast?
Please help.
Regards,
Siti
Re: How to test SIDAC?
Dear VVV,
I include here the circuit connection for you to check. Also, i would like to know the resistance value for power resistor should be.
Thanks and many regards for your support
Seety
Re: How to test SIDAC?
Hii...
could you please see the attachment file for power resistor datasheet?? i would like to know if this kind of power resistor is suitable for my case...
regards,
Seety
Re: How to test SIDAC?
Hiii…. I have try as you recommended. But when I’m increase the voltage to 200V, the both resistor were suddenly blow up!!! Hehe… also have a flame on it!!!… So, I include here the circuits for you to check just to make sure it won’t happen again. The circuit also shown...
why igniter is required for hpsv lamp
Helloo....have anybody here knows about Superimposed ignitor for HPSV lamp???
If my explanation is not quite details please ask...
Regards,
Seety
Re: How to test SIDAC?
Thanks a lots VVV... your explanation much more clear now...
But, how we can get to know the SIDAC is turns ON or OFF? or are there any method to indicate the SIDAC is turns On or OFF?
Regards,
Siti
Re: How to test SIDAC?
Thanks for the test procedure. But honestly, I still not really understand about it. I think, I still not understand the meaning of breakover voltage, blocking voltage, peak of state current at Vdrm, continuous on state DC or RMS current, holding current and peak on...
How to test SIDAC?
Hii...
I have a SIlicon Bilateral Voltage Triggered Switch (SIDAC) in high voltage lamp ignitor application. So i would like to know how to test the functionality of this components. Please help me!!. Below is the characteristics of the SIDAC:
Model: K220
Breakover...
superimposed ignitor
Hello,
i would like to explain much more details about the Superimposed(SI) ignitor to give you a rough ideas. This type of ignitor is used to ignite High Pressure Sodium Vapor (HPSV) Lamp. The application is in Street Lighting. Here is the characteristices of the ignitor...
electrical diagram for hpsv lamp
Hello,
i would like to explain much more details about the Superimposed(SI) ignitor to give you a rough ideas. This type of ignitor is used to ignite High Pressure Sodium Vapor (HPSV) Lamp. Here is the characteristices of the ignitor:
1) 70 W SI Ignitor
-...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.