Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by nicleo

  1. N

    HFSS for electromagnetic modelling of electric motor?

    Hi yasemin, I believe you should have the user manual of FLUX 2D/3D. Or, may be you can request few examples from the company.
  2. N

    Logic IC starts with 'HD' is frm which company?

    Pls advise logic IC (e.g. NAND, NOT, OR, etc), with it's label starts with 'HD', is frm which company? Thanks.
  3. N

    optocoupler working at 1-2 MHz ??

    Try iCoupler from Analog Devices.
  4. N

    How to make A/D converter work with load cell output?

    load cells Try this article: **broken link removed**
  5. N

    Articles about controlling and types of servo motors

    servo motor types Try the following articles: https://ww1.microchip.com/downloads/en/AppNotes/00696a.pdf https://ww1.microchip.com/downloads/en/AppNotes/00718a.pdf https://ww1.microchip.com/downloads/en/AppNotes/00532c.pdf
  6. N

    Integrating PIC16F877 with stepper motor

    unipolar stepper motor using pic16f877 Try the following documents: Stepper Motor Control Using the PIC16F684 https://ww1.microchip.com/downloads/en/AppNotes/00906a.pdf Stepper Motor Microstepping with PIC18C452 https://ww1.microchip.com/downloads/en/AppNotes/00822a.pdf Hopefully you will...
  7. N

    Weights body principle

    The sensor, e.g. load cell, should give an electrical output signal, either in analog or digital. See this one help or not: **broken link removed**
  8. N

    How can obtain the+15 volt or +24volt

    You can use boost converter to achieve 15Vdc and 24Vdc. You may try the online design tool frm National Semicondutor: **broken link removed**
  9. N

    Urgent : LED driver design

    wled spice model Do you mind to share which simulation software that you're going to use to model your problem?
  10. N

    Very Low Resistance Measurement (Less than 1 Ohm)

    less than 1 ohm resistor Usually we use 4-wire method to measure low resistance. You may also consider using 6-wire approach like here: **broken link removed**
  11. N

    PID Line Follower Robot, using PIC

    line following robot algorithm No PID algo was used in the document recommended by feiutm9898. However, in my opinion, we do not need PID controller for line follower... ON-OFF control or Bang-Bang control will do...
  12. N

    Can you load unix on windows machine without unix server?

    unix on windows machine Say we're using 'BootManager' to choose either one of the following OSes: WinXP and Linux. When we log into Linux, do you think we can access the files created in WinXP system? Thanks.
  13. N

    Need power supply design, 9VDC, 100mA, no transformer

    You can consider Offline SMPS. The transformer used in Offline SMPS is very much smaller. Try to look at those modern handphone chargers, they're light and small. And, you will have isolation from high voltage for safety purpose.
  14. N

    Need a good random generator for matlab

    random generator matlab Would you please elaborate in more detail how do we build a hard generators like noise from a zener diode? Many thanks.
  15. N

    operating at insufficient power

    That's true... my Fluke Thermocouple meter used Duracell batteries. After 1~2 years the meter was left unused, one of the batteries leaked chemically and damaged some parts of the meter.
See more

Part and Inventory Search

Back
Top