Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by aajizattari

  1. A

    Tetramax add_atpg_constraints and X-free response

    Tetramax add_pi_constraints and X-free response I have a small combinational circuit. I use add_pi_constraint command to set certain primary inputs of a circuit to X (unknown). e.g. add_pi_constraint X input1 Because of this constraint, certain outputs will become X. However, I want to...
  2. A

    Where the way Leads to ????

    Hi, I have started to work with FPGA's I have a Spartan 3 kit availabale I had done some examples ..... Now I want to move to this stuff like Constraints and Post P & R Routing Can any body help me by refering some material Book / link Where should I start ... what do I need to study...
  3. A

    Modelsim vs ISE Simulator

    ise simulator vs modelsim Isn't Xilinx ISE Simulator quite sufficient ??? Whats that special about Modelsim that people use i t... Plzz do list it's Features and advantages AND........... After little touch I have found the waveform Simulation to be too much time Consuming at times and...
  4. A

    9.6 khz from 27 or 33 MHz

    Hi all , I need to have 9.6 k clock from a 27 Mhz clock in FPGA But it only approximates and error is erraneous Has aanyone some Solution ????
  5. A

    can "if" statement replace "for loop" in

    Re: can "if" statement replace "for loop&quot if next statement means to skip some statements for certain conditions it's infact and if / a conditional and u neeed use another if here .
  6. A

    Help me write a 16 bit corelator (vhdl code)

    correlator vhdl HM Man give more details Tell this forum what have u done ... and where are u struck actuallly Talk in terms of Verilog and the problems u face here in Verilog
  7. A

    Help --> COUNTER WORKING

    Salam Sameem!! Is this problem solved ???? I hope it would have been!!!!!!! What u need the counter for ??? Do u want it to initialize it with load signal and then count on every clock cycle?? or u want it to increment everyy tiem u assert load The present code I hope will start once...
  8. A

    Ideas on Verilog project topics!

    projcts If u are from Communication side BCH or Convlolutional Encoder / Decoder Also, Encryption /Decryptin Module or some Compression Algorithm
  9. A

    What is wrong with my simple code?

    Yes off Course .... there is no problem with code EXCEPT Inilization of COUNT
  10. A

    FPGA Hardware (PCB) Design

    Hi, I will be required to start working on desinging custom FPGA board (for some algorithm evaluation ) including a device from Virtex Family... I am new in this ERA Kindly help me in any way u can I want to know ... related software . What about the parallel cable/JTAG support ..is...
  11. A

    Help me design a 4 bit processor

    4 bit processor Whats this exactly about..... If it was your course paper ... ask the relevant treacher for further details And if u want to do it in Verilog or VHDL U will havae a lot of References available even from Googling Especially go for Computer Architecture Groups of Various...
  12. A

    Need help with project

    hEY IS IT A TERM project or final one U seem to be in full swings of copying everyting
  13. A

    Simple exemplary programs in VHDL

    VHDL....help pls... http://esd.cs.ucr.edu/labs/tutorial/ See this Tutorial Hope this is what u want
  14. A

    Car battery charger circuit needed

    circuit car charger https://www.electronic-circuits-diagrams.com/psimages/powersuppliesckt7.shtml https://www.electronics-lab.com/projects/automotive/007/index.html
  15. A

    Which cause is dangerous ?

    Short Ciruit is most Critical and There's no Sign but A Short Circuit Itself Which type of Circuit u are talking of ??? In open wiring mechanical contact means short In PCB's etc.... it's something similar In IC's it's Internal Faults
See more

Part and Inventory Search

Back
Top