dexterpandian
Newbie level 4
- Joined
- Aug 31, 2010
- Messages
- 6
- Helped
- 0
- Reputation
- 0
- Reaction score
- 0
- Trophy points
- 1,281
- Location
- coimbatore
- Activity points
- 1,318
can any one help me how to interface 16 * 1 lcd display in 89c52
Welcome to EDAboard.com
Welcome to our site! EDAboard.com is an international Electronic Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
interfacing 16 * 1 lcd display
- Thread starter dexterpandian
- Start date
- Status
d@nny
Full Member level 5
YouTube - HD44780 16 X 2 LCD with PIC16F819 (JHD162A)
---------- Post added at 12:41 ---------- Previous post was at 12:39 ----------
I know nothing much about microcontrollers even i dont know how to programme a microcontroller perfectly but i have made lcd with out the help of any person just with the help of the HD44780 Datasheet. You should try this data sheet as it is just simplest
---------- Post added at 12:41 ---------- Previous post was at 12:39 ----------
I know nothing much about microcontrollers even i dont know how to programme a microcontroller perfectly but i have made lcd with out the help of any person just with the help of the HD44780 Datasheet. You should try this data sheet as it is just simplest
bigdogguru
Administrator
- Joined
- Mar 12, 2010
- Messages
- 9,831
- Helped
- 2,348
- Reputation
- 4,690
- Reaction score
- 2,274
- Trophy points
- 1,413
- Location
- Southwest, USA
- Activity points
- 62,510
Here are a few LCD to 8051 variant interfacing/programming tutorials:
LCD interfacing with Microcontrollers tutorial
Interfacing LCD with 8051
The majority of common LCD displays are based on the Hitachi HD44780 chip, so the interfacing is either 4-bit or 8-bit modes. Delays are critical when programming your particular MCU, the LCD will not function properly without them.
These examples should get you started in the right direction.
LCD interfacing with Microcontrollers tutorial
Interfacing LCD with 8051
The majority of common LCD displays are based on the Hitachi HD44780 chip, so the interfacing is either 4-bit or 8-bit modes. Delays are critical when programming your particular MCU, the LCD will not function properly without them.
These examples should get you started in the right direction.
ckshivaram
Advanced Member level 5
- Joined
- Apr 21, 2008
- Messages
- 5,070
- Helped
- 2,149
- Reputation
- 4,304
- Reaction score
- 2,089
- Trophy points
- 1,393
- Location
- villingen (Germany) / Bangalore
- Activity points
- 30,097
does you 16*1 have auxillary controller in it????
---------- Post added at 12:15 ---------- Previous post was at 12:12 ----------
because The Working of 16 x 1 LCD is Little Bit Different then of LCD 16 x 2.
In Most of Cases 16 x 1 LCD is available without Auxiliary Controller. Means as you see only HD44780 Controller at Back Side.
---------- Post added at 12:15 ---------- Previous post was at 12:12 ----------
because The Working of 16 x 1 LCD is Little Bit Different then of LCD 16 x 2.
In Most of Cases 16 x 1 LCD is available without Auxiliary Controller. Means as you see only HD44780 Controller at Back Side.
- Status
