Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronic Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

32 bit pic development board

Status
Not open for further replies.

manj

Newbie level 5
Joined
Dec 7, 2012
Messages
8
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,337
hi all,
for the project we have selected pic 32bit controller with 2CAN bus, graphics driver and usb. we want development board of pic 32bit controller at least with usb and graphics driver. I searched but didn't get complete information pls help me to select the development board.???
 

wp100

Advanced Member level 5
Joined
May 15, 2009
Messages
3,056
Helped
883
Reputation
1,781
Reaction score
736
Trophy points
113
Location
Prime Meridian
Activity points
0
Hi,


Seems Microchip. Mikroe and Olimex are the main providers of pic32 boards

Can and USB are internal hardware modules of the Pic chip, but think most graphic drivers are external add on parts driven by the pics software; though you give no idea of your screen type.

Microchip do have graphic software help http://www.microchip.com/pagehandler/en-us/technology/graphics/tools/software.html

A possible low cost option ? http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=2615&dDocName=en535536&redirects=PIC32USBstarterkit
 

tpetar

Advanced Member level 5
Joined
Sep 27, 2010
Messages
6,427
Helped
1,712
Reputation
3,454
Reaction score
1,677
Trophy points
1,393
Location
Pancevo-Belgrade, Serbia
Activity points
37,376

manj

Newbie level 5
Joined
Dec 7, 2012
Messages
8
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,337
hi,
we selected development board of maxi web which includes usb,graphics driver, and can,is that good?
actually we just want 1 development board of pic 32 with can, usb and graphics driver in our company we r going to do 1 project for which we need all these interface.
 

tpetar

Advanced Member level 5
Joined
Sep 27, 2010
Messages
6,427
Helped
1,712
Reputation
3,454
Reaction score
1,677
Trophy points
1,393
Location
Pancevo-Belgrade, Serbia
Activity points
37,376
hi,
we selected development board of maxi web which includes usb,graphics driver, and can,is that good?
actually we just want 1 development board of pic 32 with can, usb and graphics driver in our company we r going to do 1 project for which we need all these interface.

Its just a tool, which is used for learning or developing some product. From quality and capabilities of that tool depends what you can do with this together with your knowledge. When you start to use development board for some project you will see is this right and good choice or not.




Keep in mind this:

PIC32-MAXI-WEB WARNING

"Do not use "programmer-to-go" button when there is no image on the OLIMEX PIC-KIT3 or MICROCHIP PIC-KIT3 or that might put your microcontroller in an inrecoverable state. We have tested the mentioned scenario and we can confirm it destroys PIC32 chips (using both our and the original Microchip PICKIT3). We don't take responsibility if you brick your chip that way. For more info check the following www.microchip.com/forums/m635420.aspx".

https://www.olimex.com/Products/PIC/Development/PIC32-MAXI-WEB/
 

manj

Newbie level 5
Joined
Dec 7, 2012
Messages
8
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,337
ohh ok I ll remember it while using the development board.
 

Status
Not open for further replies.
Toggle Sidebar

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Top