Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Open-drain resistance for a pad

Status
Not open for further replies.
A

Atre

Full Member level 1
Joined
Jul 15, 2002
Messages
99
Helped
5
Reputation
10
Reaction score
1
Trophy points
1,288
Location
Eindhoven, the Netherlands
Activity points
719
Hello,

Can anyone help me with how can I specify an external resistance for an
open-drain output-pad in Design Compiler.

Thanks in advance!
 

Atre said:
Hello,

Can anyone help me with how can I specify an external resistance for an
open-drain output-pad in Design Compiler.

Thanks in advance!
Click to expand...

Are you talking about the I2C pads. If yes then I can give you, related info.
 

rajesh13 said:
Atre said:
Hello,

Can anyone help me with how can I specify an external resistance for an
open-drain output-pad in Design Compiler.

Thanks in advance!
Click to expand...

Are you talking about the I2C pads. If yes then I can give you, related info.
Click to expand...

If you can give me that kind of info......

Is it related to Design Compiler (Synopsys)?

10x!
 

Atre said:
rajesh13 said:
Atre said:
Hello,

Can anyone help me with how can I specify an external resistance for an
open-drain output-pad in Design Compiler.

Thanks in advance!
Click to expand...

Are you talking about the I2C pads. If yes then I can give you, related info.
Click to expand...

If you can give me that kind of info......

Is it related to Design Compiler (Synopsys)?

10x!
Click to expand...

Infact I can give the I2C specs doc, in which it is given how to select the external resistance value. Please go to page no. 40 of the attached doc & choose the value according to your specs(basically this value of the resistance is dependent on the supply voltage).
 

Well, that doesn't help... What I need is a way to specify in Design Compiler such thing. I mean, I know the resistance value (ie. 200 ohm) and I want to tell this to Synopsys. How can I do that??

10x!
 

may be you can add pad after DC ,add I/O pad at netlist after you had compiled by hand directly!
 

If you want to use internal pull-up resistor, you need to have this kind of pad. If you want to declare external pull-up resistor in your simulation testbench, you just need to use as like as below:

pullup p1(SCL);
pullup p2(SDA);
 

Hi, Atre

You can specify the tri-state pad for your open-drain pin. Then skip the synthesis with "dont_touch".

Good Luck
 

AlexWan said:
Hi, Atre

You can specify the tri-state pad for your open-drain pin. Then skip the synthesis with "dont_touch".

Good Luck
Click to expand...

Thank, I hope it would work this way.... I kinda dropped this for some time, but I hope I can fix it.

Thanks!
 

rajesh13 said:
Atre said:
rajesh13 said:
Atre said:
Hello,

Can anyone help me with how can I specify an external resistance for an
open-drain output-pad in Design Compiler.

Thanks in advance!
Click to expand...

Are you talking about the I2C pads. If yes then I can give you, related info.
Click to expand...

If you can give me that kind of info......

Is it related to Design Compiler (Synopsys)?

10x!
Click to expand...

Infact I can give the I2C specs doc, in which it is given how to select the external resistance value. Please go to page no. 40 of the attached doc & choose the value according to your specs(basically this value of the resistance is dependent on the supply voltage).
Click to expand...


It is a good pdf ... thanks...
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top