Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi all, I have problem my pads bus router does not start I have allresdy change the drc ro prevent the menu symbol is active but do nothing, in the help file it says :
For object mode, select the objects to bus route. Right-click and click Bus Router. The selected objects and any attached traces...
Thanks, it works and has very good options to paste, it helped me a lot,
but I still want to know if there is any way to do it in the router, because it is easier to do some manual routing in the router. But till now the only way to do that is in layout.
Thanks freinds for they help. ;)
I had worked with 1 and 1.27 pitches and I suggest you not to do that , beacuse of the high tempreture while mounting, it may cause short circiut in the board, the way is you use the pads for all but do not fanout the unused ones it, gives you the ability to use the inner layers there but not...
Re: Wich PCB Tool is better?
Hi,
I have used Orcad , ProtelDXP and PADS, but for the special case that you had said I think protel is the best choice for you because of very simple steps in Cadance and PADS package you must build up most part of the library by your self but Protel has a very...
Re: Orcad help
Hi there is another point that you must consider, the Value, usally under part at left side, must be tha same for all the parts per package, if you gaive them differing ones it cannot be considered as one package.
Have fun.
Hi all,
I am using a BGA package and I want to copy paste some same shape traces, but I cann't find any option in PADS Router, for those who use specctra I know that is specctra it is very easy to copy and paste traces I want to know the way to do it in PADS Router.
Thanks.
Hi, I have imported an orcad netlist to PadsLayout, and placed so many parts I wan t to know how to update my design with a newer orcad netlist. I also want to know if there is anyway to save a do file of my placement to prevent placeing each time, this can be done in specctra.
Thanks.
Thanks, all freinds, I have a problem in next step, does any body know how to build a part in pads, I want to build a connector that has 8 rows and 25 coloumns that the pin names and numbers are both alphaunerical, so I didn't find anything about that in the biliding part dilog box and also in...
orcad netlist header for pads
Hi,
I want to import the net list that I have generated with orcad10 to pads (.asc) but it gives me the wroung format in pads and all the elements become errors, then I recive nothing in pads layout, what must I do to correct this? Regards.
Added after 5...
Re: Fanout Spectra or layout
Thankx , I now there is no parameter to force the fanout in a degree but by adding some parameters together there is some resolutions.
Fanout Spectra or layout
Hi all,
I have a bga chip on my pcb. Can layout or spectra fanout it organized ( I mean adjustable in degree or in a way)?
Ps: Does anybody has an application note on the subject?
spectra problem
Hi all,
I have a problem with my spectra, I have placed all my components in the orcad layout. Then I export it to Spectra but there is a problem in spectra there is no GND or Power plane in the layers in the spectra although I have set that in the layout,
Looking for your...
Hi,
Orcad can make a new part schematic from verilog file, but I want to know how I can give it the pin numbers in the verilog file, Is it possible or not?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
