Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by gurunath.kadam

  1. G

    Measure stable voltage in HSPICE

    Hi, Thank you for reply. I don't know how to do this all, but I will read some documents and research online. I just have one question: Can be this done on .tr# files? Or do I need to re-run the simulations? Thanks!
  2. G

    .mt# files blank in HSPICE simulation output

    Hi, update: I ran earlier simulations with -dp # -mt # -hpp switches, when the .mt# files produced were empty. I ran same simulations with only -dp # option and now my .mt# files are properly written. But this has increased my simulation time by almost 33%! Same simulations with -dp # -mt #...
  3. G

    .mt# files blank in HSPICE simulation output

    Hi, While running HSPICE simulations with following options: .OPTION AUTOSTOP .OPTION POST=2 .OPTION MEASFORM=3 .OPTION PROBE I am getting .mt# files as blank. The output is not 'failed', but the files are completely blank with 0 bytes size. The weird thing is with same options and measure...
  4. G

    Measure stable voltage in HSPICE

    Hi, The output voltage of the oscillator I have contains spikes/glitches. Using .MEASURE TRAN MAX_VOLT MAX OUTPUT FROM=1ns TO=5ns gives me the peak of the spike but not the stable voltage reached. Same goes for the MIN function. Is there anyway to measure the stable voltage level reached...
  5. G

    HSPICE/Display SPICE model parameter for a run

    Hi, I am relatively new to HSPICE. I am trying to run some corner analyses on a small RO circuit. Some SPICE models used in the set up have some complicated equations against them sometimes few variables referencing through different files (to model the dependencies on various factors). I need...
  6. G

    [SOLVED] SystemC installation on Ubuntu 11.10

    HI mrflibble, damn.....you guys are demanding..!! :P Anyways I myself am not a very proficient systemc programmer but just a beginner. So now this next link is strictly for beginners...and I think most people must already be having this. But just to be little helpful.....(in future lets hope i...
  7. G

    [SOLVED] SystemC installation on Ubuntu 11.10

    Hello Tariq, well I can do better than that. Follow this link to integrate Eclipse as an IDE, so that people can have GUI (for better efficiency and all!) for building and running a systamc code...
  8. G

    [SOLVED] SystemC installation on Ubuntu 11.10

    Hi there, I was asking how can I compile a systemc program. I never used command lines for compiling so confused. An example of sample systemc programs given in 'examples' folder will be great. Thanks in advance.
  9. G

    [SOLVED] SystemC installation on Ubuntu 11.10

    @mrflibble........................ I am so much happy today!! :) Thnks man! Sorry but going against your preferred option, I used option A and it worked nicely. Now just trying to figure out how to use it, as I am used to GUI based systems. (Any tutorial suggestions?) Thanks again!
  10. G

    Testbench System C Symple Ram Model

    sorry for going off topic, can you please tell me how have you install SystemC? I have been trying for past couple of months and now totally frustrated. Sorry again1 and thanks in advance.
  11. G

    [SOLVED] SystemC installation on Ubuntu 11.10

    Hi everybody, I know most people have faced same problem. After extensive search and trying various options i am putting a request here. My OS: Ubuntu 11.10 Target SW: SystemC-2.2.0 after exploiting various options like 1. direct ./configure in systemc-2.2.0 folder and 2. in objdir; I am...
See more

Part and Inventory Search

Back
Top