Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by akrishna71@gmail.com

  1. A

    3 NOT gate connected，whats for？

    ya , for delaying purpose they were added the three NOT gate's , its becoming the timing diagram basis . the output inverted value is delayed for some seconds , thats why i think added the extra two NOT gate,.
  2. A

    if place the component in the board get as overlap ,whether it can error or not?

    hi buddy's i am using orcad software for pcb board designing, i have net listed the circuit , and while place the components getting overlap , because the board dimension is poor. so my doubt is whether if i place the component like this whether i get the error or not while...
  3. A

    how am i become as you like good pcb board designer?

    thank you buddy, ,. i will try as you told ,.,,..,..
  4. A

    how am i become as you like good pcb board designer?

    hmm , okay thanks ,. i will do it,. and can i meet in other way? like mail ,and facebook,.,,...,
  5. A

    how am i become as you like good pcb board designer?

    hum, okay thanks tpetar ,..,..,..,.,i will follow as you told , thanks again,...,.,. - - - Updated - - - okay marce , thank you for your reply ., i shall use this link
  6. A

    how am i become as you like good pcb board designer?

    hi Super Seniors , i am Ramakrishnan , from india, i just done Bachelor of engineering in the field of ELECTRONICS AND COMMUNICATION ENGINEERING , Basically i have interest in the electronics field. for that i just finished orCad course without appropriate teaching, so now , by my interest in...
  7. A

    here some error in the circuit (ohm meter circuit)

    hi ,, buddy thanks , i worked it ,,, do you know how to use the Altium designer? if you have the software , please send the link to me,, i need it.,.,..,.,.., free download link just send to me ,,, thanks .,.,.., waiting for your reply
  8. A

    here some error in the circuit (ohm meter circuit)

    first of all thanks for reply dude, i have a doubt , then why don't you use that LM317L here , and my opamp also dual supply ,,..,,..,.., which software did you done it?
  9. A

    here some error in the circuit (ohm meter circuit)

    hi buddy's here i have attached my circuit, i have small in this ... that means i have drawn the circuit in the orcad 16.0 and practically checked this circuit i didn't get the noted output in both ways ,,,, in this two condition should i connect the input 5V with the...
  10. A

    how to and what are the rules and ways create the foot prints?

    hi seniors, i have doubt create the foot prints in orcad , i created one project and in which one 15 pin connector there. for that i just wanna create foot print ,but everytime i am getting error like pin 1 is missing pin 2 is missing likewise all pins . i had used that orcad pcb designer...
  11. A

    not updating pcb board while netlisting

    ok , thanks , give some ideas to create a new foot prints ,,, rules and procedures ,,,
  12. A

    not updating pcb board while netlisting

    i don't have a words to say ,,, yes i am beginner for or cad & circuit designing ,,,,,, see you are my senior so you have full rights to tell anything, i am eager to contact with you , for further contacts i just need your facebook id name & profile pic name ,, please tell to me, i don't...
  13. A

    foot print created rules for symbols

    hi buddy's i am using orcad16.0 and i created one project , created footprints for corresponding symbols, even also i shows some error while netlisting IT shows some refdes error , but i gave the name of the symbol while creating the foot prints, but no use couldn't clear...
  14. A

    ERROR while netlisting

    hi dudezz,, i am using orcad 16.0 , and i have tried so many times ,but unusually i did not get error less circuit and board .,., so please guys take your time for my project , please consider it i have attached my three project and created foot prints also , you know its having...
  15. A

    not updating pcb board while netlisting

    take your own time buddy ,........,.,.,.,.,.
See more

Part and Inventory Search

Back
Top