Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi All.....We have a problem.....
Company has purchased Solidworks PCB 2020 to link in with the mechanical side. Currently most PCB designs are on P-Cad 2002/2006.
We have also upgraded the hardware.
Now this is where the problem comes in.
The licence codes for P-Cad 2006......Well no one in IT...
Hi All, been a while.
Well the powers that be have decided to buy NI (Ultiboard/Multisim) on advice...........
Muddleing my way through. But HOW do you get it to pick up a component/part at the ref point? (a blue square & cross)
Tried the NI solution of a fine 0.00001 grid but no. Once you...
Update
Got hold of PDIFOUT5.EXE & EXP
When I tried to convert I got this message:-
os289: Cannot remove kernal. Another program has been installed on vector chain.
mmm.....lost
Regards
Russ
Hi all
A problem with PDIFOUT.EXE
Have been using this to convert old DOS circuits to P-CAD 2002 with no problem.
Anyway, went to use it yesterday to convert a circuit, and it started to run, then came up with:
ERROR: Could not open Message file.
Not had this before, and as said was working...
Hi BG
Thanks for your reply.
Yes, I can/have done that.
The thing is we have custom title sheets (created by my predecessor) that are ".tbk" files that I normally use. Go to "Title Block Select" then pick a relevent sheet size "SHTA2PCBsht.tbk" pick the layer and "Modify". Its then a case of...
Hi All
P-cad 2002.
Does anybody know how to create and or modify an existing title block/drawing format.
Not had to do this before as all the designs have fitted on our existing A3 or A2 blanks, but have a large board to do (500 x 500) so have to create a A0 drawing sheet, and for the life of me...
Hi
Create your footprint, but position the component origin (pick point) the radius of your circle away, so when you select the component it will rotate around the circle centre.
If the LED's are to be positioned equally around the circle, then divide 360 degees by how many LED's you have and...
p-cad dos versions
Brilliant, it works a treat.
Thanks very much B.G.
While waiting for some feedback on this problem I relaid the board.
It wasn't to much of a problem, was simple and only took about a day. BUT I don't know what other historical horrors await, so solving the problem could...
pcad import
Thanks for your reply B.G.
When you say "replace in PDF DBunit CMM" What do I actually need to do. Modify the PDF file? if so how? If I double click/open it, it just says "Adobe Reader could not open as it is not a supported file"
Russ
pcad dos
Hi all
Problem with P-Cad DOS into P-Cad2002
Have one of our old DOS designs to modify which was laid out in METRIC. (here it comes)
When I PDIF'ed the design in, it came at scale 2.54!!!! (a bit big)
I changed "OPTIONS-CONFIGURE-UNITS" both ways (metric & imperial) and read it...
Hi
I'm trying to get a old DOS schematic V5.02 into P-Cad 2000.
I've run PDIFOUT and got the pdf file. BUT on trying to import it, it fails and i get an error report with:-
Error: Unrecognized syntax near line 5703.
Any ideas?
Russ
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.