sim900 ATD*101#; problem

[ognjan]

SIM900 can't execute command: ATD*101#;

What is solution ?

 

[ckshivaram]

can you execute all other basic commands.... and is 101 a valid number in your country

 

[ognjan]

can you execute all other basic commands.... and is 101 a valid number in your country

Yes, all other commands work ok.
I make GSM controllers many years...
(> elektronika.rs.ba)

Everything works fine... Siemens mobile phones and Siemens GSM module, even on sim300.

Call *101# is code for check prepaid account, and only this call don’t work with SIM900 modul (return ERROR).

 

[CADiLO]

Update firmware SIM900 to 7 version.
And no use ;
ATD*101#

; used voice call only

 

[seadolphine2000]

The command syntax is:
ATD#;
Where "#" is the complete format of the number and, the ";" tells the MODEM that this is "Voice Call" not a "Data Call"

I tried this command many times on different phones and MODEMs.

Hope this helps.

 

[ognjan]

Update firmware SIM900 to 7 version.
And no use ;
ATD*101#
; used voice call only

BUT THIS IS VIOCE CALL!
Answer, of mobile operator is plain text (account and date of expiration of SIM card). Is it the same for most of the Countries?

---------- Post added at 14:21 ---------- Previous post was at 14:19 ----------

Update firmware SIM900 to 7 version.

Where I can find flash software and flash file ?

 

[CADiLO]

Nooooo!!!!

This not VOICE - this CUSD.

Correctly call for SIM900:

AT+CUSD=1,"*111#" // for Kievstar - Ukraine // ( or AT+CUSD=1,"*101#" for UMC )
OK
+CUSD: 0,"Na rahunku: XXX.XXgrn; Xhvyl;Info pro bonusy na *112#,*118# i *119#. Zagubyv svoiu SIM? Vidnovy ii! Info:XXX*XX*",XX

or

ATD*111# // for Kievstar - Ukraine // ( or ATD*101# for UMC )
OK
+CUSD: 0,"Na rahunku: XXX.XXgrn; Xhvyl;Info pro bonusy na *112#,*118# i *119#. Zagubyv svoiu SIM? Vidnovy ii! Info:XXX*XX*",XX


AT+GSV
SIMCOM_Ltd
SIMCOM_SIM900
Revision:1137B07SIM900M64_ST

>>>Where I can find flash software and flash file ?

check distributor in your region

 

[ognjan]

>>>Where I can find flash software and flash file ?

check distributor in your region[/QUOTE]

I’m find flash software and firmware v.7 file (in attachment), but I’ have a problem in update procedure

 

[tompas123456]

Add command

AT+CSCS="GSM"

 

[Pooker]

Hello all,

i am having the same problem i did try
AT+CSCS="GSM"
OK

please help

 

[tompas123456]

Try using this command.

at+cusd=1,"*101#" \r

 

[Pooker]

Hello got the solution!!!

switch power off until it ask you to switch on the flash untility. Have patients wait a while!

It works any probs ask me!

Ally

 

[tompas123456]

After reset module add command at+cusd=1\r" // ---->Enable unstructer service

 

[Pooker]

Hello,

tried
at+cusd=1\r" //
error

Anyway that infernal continous ringing has stopped. Probably sorted out the other bugs too!

2.45 am going to bed

Thanks

Ally

 

[ThiVu]

>>>Where I can find flash software and flash file ?

check distributor in your region

I’m find flash software and firmware v.7 file (in attachment), but I’ have a problem in update procedure

Check the baud rate..
I see it is 460800 ???

 

[hamedtv]

i think you load the wrong ver of binary file
you cant use this module agane

 

[DeagLe]

>>>Where I can find flash software and flash file ?

check distributor in your region

I’m find flash software and firmware v.7 file (in attachment), but I’ have a problem in update procedure

[/QUOTE]

Where is attachment ? I cant see it.

 

[hamedtv]

dear friend
first select 56k speed
then press start
power up the module and do not free the power key for 10 sec
if do not work
press again start
active reset of module for a moment

 

[Raj2011]

Hi ,i need AT coomand for a SIM990A module to auto answer a voice call,can any one help pls,ATSO dosnt seem to work.
thx and regards.

---------- Post added at 10:47 ---------- Previous post was at 10:47 ----------

command* sorry miss spelled.p***

 

[ckshivaram]

what is the value you have set for ATS0

try giving ATS0=2 or 3.