Programming SHT11 using PIC24FJ16GA002. SHT11 not responding

odcbbits

Hello guys,

I have been working on SHT11(Sensirion Temperature/Humidity Sensor) for a long time now and using PIC24FJ16GA002. I am still stuck on the first step as the sensor is not responding. I thought i burned the sensor and tried a new one but i am having the same problem.

At the moment i am just trying to get an acknowledgement from the sensor when i sent it a command but its not responding. Following is my code in oder to recieve this acknowledgement. Please help.

#include "p24fj16ga002.h"
#include "math.h"
#include "stdio.h"
#include "string.h"

_CONFIG1(JTAGEN_OFF & GCP_OFF & GWRP_OFF & FWDTEN_OFF )

_CONFIG2(IESO_OFF & FNOSC_FRC & FCKSM_CSDCMD & OSCIOFNC_OFF)

// DATA AND SCK set to 1 or 0
#define DATA_SET_1 LATBbits.LATB3=1
#define DATA_SET_0 LATBbits.LATB3=0

#define DRAIN ODCBbits.ODB3 = 1

#define SCK_SET_1 LATBbits.LATB2=1
#define SCK_SET_0 LATBbits.LATB2=0

#define DATA_OUT TRISBbits.TRISB3 = 0
#define DATA_IN TRISBbits.TRISB3 = 1
#define SCK_OUT TRISBbits.TRISB2 = 0

#define READ_DATA PORTBbits.RB3

#define MEASURE_TEMP 0x03 // 000 00011
#define MEASURE_HUMI 0x05 // 000 00101

#define TEMP 0
#define HUMI 1

#define NOACK 0
#define ACK 1

// FUNCTION USED TO CREATE THE DESIRED DELAY IN THE PROGRAM

void delay(unsigned int delay_count )
{
int i, j;
for(i=0;i<delay_count;i++)
{
for(j=0;j<delay_count;j++)
{
asm volatile("nop");
}
}
}

void connection_reset()
{
DATA_SET_1;
delay(5);
int i;
for (i=0;i<10;i++)
{
SCK_SET_1;
delay(50);
SCK_SET_0;
delay(50);
}

}

void main()

{
AD1PCFG = 0xff;
DRAIN;
int test = 1;
unsigned int i =0;
//unsigned char value=0;

//unsigned int error;
//unsigned char value=0;
//trans_start();

delay(400); // 11 ms after start up

SCK_OUT;
DATA_OUT;

connection_reset();
delay(50);


//DATA_SET_1;
delay(50);
SCK_SET_0;
delay(50);
DATA_SET_1;
delay(50);
SCK_SET_1;
delay(50);
DATA_SET_0;
delay(50);
SCK_SET_0;
delay(50);
SCK_SET_1;
delay(50);
DATA_SET_1;
delay(50);
SCK_SET_0;
delay(50);


for (i=0x80;i>0;i/=2) //Transmitting the command
{
if (i & MEASURE_HUMI)
DATA_SET_1;
else
DATA_SET_0;

delay(50);
SCK_SET_1;
delay(50);
SCK_SET_0;

}

DATA_IN;

while (READ_DATA==1)
{

}

test=0;


}

According to the datasheet the maximum frequency is 1 Mhz if power supply is less than 4.5V. I am using a power supply of 3.3 V and my frquency is very low about 8 Hz.

Any help is greatly appreciated.