I'm looking for pic programmer for 24F series

[eemkutay]

pic24f programmer

Hi, Friends

I have been using ICD2 with PIC16F876A and It's been working for PIC16 and PIC18 series perfectly. I also have a few PIC24FJ32GA002 but my ICD2 is not supported this series because of 3V3. Some of friends on the net say, "We can program with ICD2" but I dont know How?

Please, Can you give me a PIC24F series programmer link?

Advance in thx.

 

[BlackOps]

pic24 programmer

**broken link removed**

they say it can program PIC24

 

[eemkutay]

pic 24f programmer

@BlackOps

Thx for link but I know Pickit2.

I'm looking for free programmer.

 

[foxabilo]

icd2clone 24f

So long as MPLAB updates the firmware in your ICD2 design all you need to do is pop either a level shifter on the output lines or a few impedance matching resitors, also most modern PIC chips that are in the ICD2 (if its home built) are very tollerant of voltage ranges so you could just add a second voltage regulator with a jumper, OR I think the ICD2 design has a pin that changes for different voltage applications so you could switch it using that (that last point I don't know for sure but Its in my head as being true)

 

[eemkutay]

programmer for pic24

@foxabilo

thank you,

I think , I must buy a pickit2 programmer. It's just 40$ and all of pic series are programed.

 

[picnoobie]

pic24h programmer

try this I used it Pic24H and now. dsPic33F.
you only need the small pcb which is the level translator,
I got the info from one of the threads here.

good luck!

 

[elec_gu]

pic24f programer download

Hello,
although it seems hard to believe, the first programmer which I had, the “epic” parallel port programmer (from 1998!), is perfectly able to program those pics.
Software here:
hxxp://www.melabs.com/support/progsoft.htm (the beta sofware)
The instructions here:
hxxp://www.melabs.com/support/3v_icsp.htm (section EPIC Parallel Port Programmer)
The circuit/pcb are very easy to find.

best regards

 

[eemkutay]

pics 24f

@picnoobie

thx for link

The voltage translator really seems to work. I'll try it. Thank you again.

@elec_gu

I'll try the voltage translator circuit. Thank you

 

[bhaveen]

programmer for pic24h

I suggest you to update MPLAB IDE.
Install version 7.61 available for free download.

 

[mjane]

design pic24f programmer

Hi, Friends

I have been using ICD2 with PIC16F876A and It's been working for PIC16 and PIC18 series perfectly. I also have a few PIC24FJ32GA002 but my ICD2 is not supported this series because of 3V3. Some of friends on the net say, "We can program with ICD2" but I dont know How?

Please, Can you give me a PIC24F series programmer link?

Advance in thx.

Hi.. you may try Hi-tech Software.. ANSI-C Compiler.. =)

 

[mosses]

24f pic programmer

Hi, Friends

I have been using ICD2 with PIC16F876A and It's been working for PIC16 and PIC18 series perfectly. I also have a few PIC24FJ32GA002 but my ICD2 is not supported this series because of 3V3. Some of friends on the net say, "We can program with ICD2" but I dont know How?

Please, Can you give me a PIC24F series programmer link?

Advance in thx.

Hi.. you may try Hi-tech Software.. ANSI-C Compiler.. =)

Thanks...

 

[Kova]

pic24f programmieradapter

try this I used it Pic24H and now. dsPic33F.
you only need the small pcb which is the level translator,
I got the info from one of the threads here.

good luck!

Hi,
I want to build this little mod to use it with PiCS B ICD2 clone.
I have a question:

What is the different between VCC_T and VCC line?
In the scheme, the VCC line is connected directly to USB +5V; but on the VCC_T signal (VDD in the ICD2) also there are 5V :|?
Why I can't connect together the Pin 3 and the Pin 10 of SV1?


In the Mplab software i can't disable the "Power target circuit from MPLAB ICD2", right?
Thanks all!
Bye

 

[hassan1980]

programator pic24fj

try this I used it Pic24H and now. dsPic33F.
you only need the small pcb which is the level translator,
I got the info from one of the threads here.

good luck!

Would you please uplaod the Hex file

 

[picnoobie]

programador pic 24f

hassan1980:
The hex file is the one from PiCS rev B can be found icd2clone.com,
(except for the pin headers and a jumpers, this is the same layout of PiCS')

Kova:
VCC_T is the from the target device which if you use this for Pic24/dsPic33 would
be 3.3v, VCC is the usual 5v. You have to uncheck "Power Target from ICD" in Mplab
if you use this circuit.

 

[Kova]

programmer+pic24

VCC_T is the from the target device which if you use this for Pic24/dsPic33 would
be 3.3v, VCC is the usual 5v. You have to uncheck "Power Target from ICD" in Mplab
if you use this circuit.

Thanks picnoobie for the help
So the VCC_T is a voltage (3.3V) that I must supply externally (from the target), right?

 

[picnoobie]

microchip pic24f programmer

So the VCC_T is a voltage (3.3V) that I must supply externally (from the target), right?

yes.

 

[Kova]

pic 24f program

[yes.

Thanks

 

[hassan1980]

pic24 programmer

picnoobie

This project needs two micros 16F877 for programing then 18F4550 to communicate via USB, Is it correct?

 

[picnoobie]

pic serie 24 f

hassan1980:

Basically yes, look at icd2clone.com, and the other thread for more information.

 

[hassan1980]

programmer for pic 24f

picnoobie

Dearfriend, What's about connecting zif Socket to the ICD2?