Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronic Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

how to design a microcontroller circuit!??

Status
Not open for further replies.

deah

Junior Member level 1
Joined
Jul 16, 2007
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
philippines
Activity points
1,406
:cry:

anybody could help me have this one??
 

ubna

Advanced Member level 4
Joined
Jul 25, 2007
Messages
112
Helped
14
Reputation
28
Reaction score
5
Trophy points
1,298
Location
India
Activity points
1,819
If you are going for a full design and implementation,
1) Write down the features for the microcontroller you are going to design
2)Design an architecture diagram that could meet with all the features of your microcontroller.
3)write codes in verilog or vhdl for each block in the architecture diagram and simulate it in tools like fpga advantage or synopsis or ncsim.
4)once simulated, it can be synthesized using tools lie precision synthesizer or rtl compiler..
 

    deah

    points: 2
    Helpful Answer Positive Rating

deah

Junior Member level 1
Joined
Jul 16, 2007
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
philippines
Activity points
1,406
Actually my projects is the one thermometer sensor..
it's like, we're making a display thermometer..
that thermometer should measure the temperature of the desired area,, and everyone can see it just like a digital clock..
somebody told me to first design a temperature sensitive circuit..
i have been given the diagram and he said i
may interface thst design to a microcontroller circuit that can ADC and drive the LCD display...

how could i make it step by step?
can you help me??
 

rina_1220

Member level 2
Joined
Jun 2, 2006
Messages
50
Helped
4
Reputation
8
Reaction score
1
Trophy points
1,288
Location
Brazil
Activity points
1,616
which microcontroller are you using?

first of all, you have to choose all the components you are going to use and then take a look at all components' datasheets.
Secondly, I think it's good if you organize things deciding which uC pin controls what in your application. In your situation, I think it'd be enough just 8 bits for the display (no matter what sort of display you are using) and 1 pin for the ADC (if you choose a uC with internal ADC).
Then, if you already have the sensor circuit, all you have to to is connect the output signal of the sensor circuit to the ADC and (supposing the ADC is inside the uC) the LCD too to the uC.
This is pretty simple. Just don't forget VCC, GND to your circuit and oscillator to the µC.

I hope that helps you:!:
 

    deah

    points: 2
    Helpful Answer Positive Rating

deah

Junior Member level 1
Joined
Jul 16, 2007
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
philippines
Activity points
1,406
i know it will help me more than much..
thank you..
i appreciate your kindness..
thank you..
 

rina_1220

Member level 2
Joined
Jun 2, 2006
Messages
50
Helped
4
Reputation
8
Reaction score
1
Trophy points
1,288
Location
Brazil
Activity points
1,616
don't mention it.
I hope you get to assembly it easily now. :D
 

    deah

    points: 2
    Helpful Answer Positive Rating

deah

Junior Member level 1
Joined
Jul 16, 2007
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
philippines
Activity points
1,406
okey..
thank you..:D

Added after 1 minutes:

thank you..:D
 

Status
Not open for further replies.
Toggle Sidebar

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Top