Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by worst

  1. W

    questions about "CDS_Netlisting_Mode" (IC5.0.0)

    17: cds_root: not found Hi! Thanks again. I have use the command "getShellEnvVar("CDS_Netlisting_Mode")" to check, the result is "Analog".So it means the CDS_Netlisting_Mode set is right. Or it's a bug of 5.0.0? Maybe the problem is because the license?Can you tell me how to check the license...
  2. W

    questions about "CDS_Netlisting_Mode" (IC5.0.0)

    export path=$cds_root/tools/bin First,Thank you very much for your kindness:> I'm not familiar with the Linux, and so i modify the .bashrc as your said. But, unfortunately the error is also exist. This is my ".bashrc" now: CDSDIR=/IC5 CDS_ROOT=/IC5 CDS_INST_DIR=/IC5...
  3. W

    questions about "CDS_Netlisting_Mode" (IC5.0.0)

    cds_netlisting_mode I have some questions about using IC5.0.0. When I run a trans simulation in AE(the circuit include a pluse voltage supplier),I get a error message:"Error found by spectre during hierarchy flattening. V1: Waveform type must be specified if any waveform paras are given."...
  4. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    cadence licence setup So you mean don't use Candence to make the netlist?
  5. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    cadence vsource help Thank you very much. And I have 2 questions: 1.If it's a bug, how to resolve it?Are there other library to supply Voltage and Current source? Or, we must build a source by ourself? 2.When I use Cadence in university lab(don't know its version), I havn't meet this problem...
  6. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    waveform type must be specified vpulse I run spectre for Analog Design Environment. And if I replace the Vpluse with Vdc, there're any errors. So i think the problem is caused by Independence source.
  7. W

    RF and Microwave Testing and Equipment

    I have some book and paper about them.But they are larger than 10MB. So if you give me your e-mail address, I can sent it to you.
  8. W

    How to fix this Cadence IC5033 error message???

    fix cadence is it at start of candence?
  9. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    vsource cadence Vsource?what's you mean?
  10. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    waveform type must be specified So,you mean my license setup is wrong,is it right? Thanks very much. Added after 2 hours 55 minutes: Thank you.I have solve the license problem. But i meet another problem: When i use simulation by spectre,there's an error. Error found by spectre during...
  11. W

    Cadence 5 problem with missing icons in Schematic Editing Mode

    I am a new cadnece user.And i meet a problem after install. In the Schematic Editing Mode,there are only five icons(save,zoom in,zoom out,propert,repeat) in the tools bar(left side).I know there should be other icons. I don't know what's the problem,license,setup,or other reason? my OP:redhat...
See more

Part and Inventory Search

Back
Top