Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
A reply to myself:
For curved structure, I couldn't find a way to expend the curve as a true curve.
However, a comprise that works for me is I instead specify the segment number, and set it to resonably high.
This is OK as at the end from AutoCAD I will also be doing the same to generate a...
Hi,
I have got some resonator drawn in HFSS, and would like to export them to AutoCAD.
I did it using the export, as dwg, and in AutoCAD I was able to import and everything seems to work, until I realized the curve I see in AutoCAD was very blocky, the bends were not smooth at all.
Is there a...
Hi,
I am simulating to find the resonance frequency and measured quality factor of some CPW transmission line resonator with a short circuit as termination.
They are coupled to the feedline via a series coupling capacitor.
I set the length from the coupling cap to the short-to-GND, then I...
Hello,
I am using Driven Terminal for my simulation with some 50Ohm CPW waveguide.
On getting the results, I want to simulate for the given power in dBm, how much current I will end up running through some sections.
However in Driven Terminal the excitation is in terms of incident voltage.
May...
Hello again,
May I know more about the method you are describing?
I was originally confusing it with de-embedding the two feeding lines in series with the ICAP,
however a later revisit to this thread, I realized that you were talking about CPW line with length of ICAP, may I know how exactly it...
Hello,
Thanks a lot for your reply,
I was able to de-embed using an internal function which can be set at the excitation.
Lately I am following another HFSS simulation regarding a parallel plate capacitor, which I think might be a better starting point.
They were using just 2 pieces of metal...
Hello,
I am trying to extract the capacitance of an interdigitated capacitor along a CPW waveguide.
I have been trying different ways, from using Y-parameter by modelling the the thing as a pi-network, however I didn't get something reasonable with the calculated capacitance being heavily...
I am pretty frustrated, though I am not quite confident with the expression, in which I call the surface, take a dot product of the vec_H with the normal to that surface, and then integrate the dot product over that surface, I am getting a fluctuation like below, while I expected an exponential...
Thanks a lot, in fact I am getting numbers pretty close to the expected, however the thing bothered me is when I tried to plot the flux normal to the square, I get fluctuating values, instead of the exponential decay of field I expected.
However from the vector plot, I do see the arrow...
Sorry if this is a duplicated question, but I am working on this and hope to extract the data within this week, after some tries I decided it maybe better to seek advice.
It's actually the same simulation I was running in a previous question:
https://www.edaboard.com/threads/327356/
The...
Thanks a lot for your advice.
Yesterday I tried to define an extra structure, that is a ring surrounding the square hollow and sized within the strip line,
then I refine the mesh only within that ring, and it worked pretty well in greatly reducing the resource needed while keeping a good...
Hi,
I have been simulating some CPW waveguides, and with a small dimension like 13um wide of the center lines and 7um gap, then I have a small square hollow within the (blue) CPW center line as 4x10um.
I wanted to simulate the H field being coupled through that square by the red CPW line...
Hello,
I have been trying to characterise some IDCs using HFSS, but I haven't got any luck confirming my results, in a way that I don't understand which is the correct way to extract the capacitance.
What I have been doing is to draw a layout mentioned on a paper with the dimension and circuit...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
