Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hello,
There are lot of Microcontroller's in Cypress Family.
what should be considered to select a PSOC4 CY8CMBR3XXX Family Microcontroller fo my touch panel? or which PSOC4 CY8CMBR3XXX Family is best to use for the touch sense?
Use two resistors as voltage divider.
But i need to get the required range. Voltage divider can't give the required range with the change in input of op-amp. i mean i suppose to get a gain 0.33 and output with 2.9VDC to 4.8VDC with the change in input 0.6VDC to 3.2VDC.
Thanks.
Hello,
How to adjsut gain in required range minimum and maximum i.e 0.6v to 3.2v equals to 2.8V to 4.8V?
This range is required for transconductance of the Mosfet.
Dear klausST,
Thank you for your response.
Specifications:
Input will be 230 VAC 50 Hz.
CURRENT: precise 1mA to 1 Amp
VOLTAGE: 0-24v
And also please suggest, after completion of electroplating etching there will be a sudden high voltage change.
So i need to sense the sudden voltage change...
Hello every one,
please i need a best suggestions from you.
I need to prepare adjustable voltage and current for electroplating.
And also please suggest me how can i sense the high voltage at the output.
I need to sense a high dc voltage after completion of electroplating and the voltage is...
Hello,
Please need a suggestion on Plating thickness tester. currently working on the project. As you know there must be constant current source constant current source for the application.
So how can built or Is any ready made available in the market. because i don't have luxury time to built...
Hello friend,
Am facing the problem stacked in frequency measurement.
i need to find the frequency of mains transformer that is 50hz. I know there is is an IC LM331 which can be used to convert frequency to voltage, Problem is it is impossible to connect mains AC direct to an IC. So in between...
Hello Everyone,
One of my project is going on RPM Sensor (Inductive type) where i want to monitor the readings of the sensor by the micro controller where the controller needs 5VDC from RPM sensor.
Problem is that i know only these details about the sensor,
* RPM Sensor is an inductive type...
Dear Prabhukaran3,
OrCAD can create differenrt type of netlists for different tools. One of the way from OrCAD to PADS is just annote the design make a design check rules without any error.
Then goto project window click on .dns file. Go to CREATE NETLIST --> OTHERS. In others select...
Please suggest me,
Here am using 0-6 V 500 mA transformer. I need theoretical calculation for change in output voltage with the change in input voltage.
here i have the formula for Primary turn Np=(Vp*10^8)/4*1.11*Fo*AC*Bmax
Where Bmax=maximum flux density in guass
AC=...
Hello Everyone,
Wishes for the day.
The project is about to bring up a board.
By using potentiometer i need to vary current range from 1mA to 2mA with the input voltage of 1.5 to 3v and current resolution must be 0.1mA or above will be better.
So, i need to make components selection before...
Thank you kapil. I got it. Small doubt bro, i have created MIC29302 smd regulator. But the problem is how to create heak sink below the regulator cap (I mean the dots on the board) in Pads layout.
Thanks & Regards
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
