Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by engurucuklu

  1. E

    Is it right approach to design?

    i'm sorry. i agree with you. I have control circuit. it is for driving e.g. motor,gates. some components are microcontroller,triacs,power transistor. yes there is 220AC. I wonder. can i put this circuit in single chip with mixed signal approach. is it profitable point of view cost(for big...
  2. E

    Is it right approach to design?

    Hi, I have control circuit board on which has microcontroller, analog inputs, triacs and high voltage. usage for motor drive e.g.. may be it is bad question but I wonder that may the board be implemented with analog-digital approach on chip. is it profitable? thanks in advance
  3. E

    new configuration for EDA tools

    thanks. i am trying rh8 now. because of price and being new with system configuration, we enjoy pc.
  4. E

    new configuration for EDA tools

    Hi, we want to use mentor ic flow and associated tools. (2004.2) wich hard and soft platforms, do you advise? cpu? ram? harddisk? graphic card? which redhat version will be good? (we tried redhat 7.x and 8.0 with sata and pci-e graphic card.,there are lots of problems. we are beginner in...
  5. E

    How to find a critical path and what software to use?

    exploring critical path Hi, i am beginner as below shown. I want to find "critical path" but i can't accomplish. I have these programs: Altera quartus 4.1 WE, Silos2001 demo, TimingTool and HSpice. Can One of these (restricted) programs have ability of solving this issue. If yes. How can i...
  6. E

    Looking for documents about FPGA and CPLD architecture

    Re: FPGA Architecture I'm sorry "arunragavan" i don't understand you exactly. But thanks for your interest. "hamadeh" Although i glanced over the thesis, i can say it will help me. Thank you.
  7. E

    Which antenna is the best for 750MHz frequency?

    Re: Which Antenna for 750MHz "mdturan20002000","sergio mariotti","MACRF". Thanks for your interest. I mean omhic loss and SWR for efficiency. We asked our teacher and he approved µstrip. Frankly speaking i want to design interesting one. i think µstrip can answer our need. If you design any...
  8. E

    Looking for documents about FPGA and CPLD architecture

    Re: FPGA Architecture thanks for your interest. "FPGA and ASIC" comparison and "FPGA and CPLD" slide copy are both informative. But they can't answer my need. as i posted in request part, these books can help me that i found. But i can't get anyone. Architecture and CAD for Deep-Submicron...
  9. E

    Looking for documents about FPGA and CPLD architecture

    Re: FPGA Architecture "dddhacker", i followed your advice. i will compulsorily use them fragmentary. On the other hand i don't understand why down quantity is increasing exponentially.(?) that doesn't mean i don't need another advice. thanks.
  10. E

    Looking for documents about FPGA and CPLD architecture

    Re: FPGA Architecture Thank you. But "Design Warrior's Guide to FPGAs" doesn't answer my requirement. It contains rather different design flows expect early few chapters. I need to know how FPGA chip can be designed with different approachs at RTL.
  11. E

    Looking for documents about FPGA and CPLD architecture

    FPGA Architecture Hi, I searched net and found few insufficient sources. I need to learn architectures of FPGAs and CPLDs. Which approaches are point at issue? Can you advise book or source that discuss this point widely? regards,
  12. E

    Which antenna is the best for 750MHz frequency?

    Which Antenna for 750MHz For antenna lab our group get 750~MHz antenna design. We will get point according to efficiency. we considered microstrip antenna but to tell the truth we don 't know from which we can get enough result. For this frequency which type antenna should we use. regards,
  13. E

    Anyone use MATLAB in VLSI designing

    matlab for vlsi which toolbox can i use for vlsi design. is it in standart boxs.
  14. E

    fuzzy logic controller design

    Hi, We are discussing about designing fuzzy logic controller for undergraduation thesis between 4 ee students in my department. I think i can be good project. But i wonder that we can archieve it. Is there anyone studied on this design? for which complications we must prepared? i am open...
  15. E

    Analog Simulation Software?

    i agree hspice is professional. i used pspice. But i don't exactly know restrictions. There are lots of free spice versions. Which one is the most capable?

Part and Inventory Search

Back
Top