Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by cristianb

  1. C

    Design Management softaware

    Hello, Does anybody has experience with DM software in a dfII framework. I'm trying to choose one, and I looking for some real user quotes, not the sales bullshit that I found until now. What is the overhead of setting it up and using it, ease of integration into cadence, drawbacks, etc. Tank...
  2. C

    Design Management software fo DFII

    design manager dfii Hello, Does anybody has experience with DM software in a dfII framework. I'm trying to choose one, and I looking for some real user quotes, not the sales bullshit that I found until now. What is the overhead of setting it up and using it, ease of integration into cadence...
  3. C

    Documents about ADC for Blu-Ray

    Re: ADC for Blu-Ray Here is the paper (sorry it was in ISSC) A CMOS multi-format read/write SoC for 7/spl times/Blu-ray/16/spl times/DVD/56/spl times/CD https://ieeexplore.ieee.org/iel5/9995/32118/01494124.pdf?tp=&isnumber=32118&arnumber=1494124&punumber=9995 You might find these interesting...
  4. C

    IC design in Austria?

    Infineon has a few design center in Austria in Gratz and Villach.
  5. C

    Documents about ADC for Blu-Ray

    Re: ADC for Blu-Ray Are u talking about the ADC on the Read path or on the servo detection loop. Anyway both are dependent on the overall channel architecture used. You can consul a paper publishet by some guys at Mediatech in JSSC about this, it will give you some more info.
  6. C

    PhD of digital IC design looking for a job

    Post a CV maybe you'll get lucky
  7. C

    Is there any company needs foreigner employees?

    You also could find work in eastern europe where is a shortage of IC designers at the moment
  8. C

    Single Electron Transistor can be use in analog design or no

    Re: Single Electron Transistor can be use in analog design o In digital design basically you operate a transistor in on or off mode, as opposed to analog design where mainly you work on the transition slope between the on and off mode - here you can exploit the gain function of a transistor...
  9. C

    difference between HSpice and SpectreS or Spectre in cadence

    Re: difference between HSpice and SpectreS or Spectre in cad check this topic. it should answer most of your questions
  10. C

    Process Variation simulation

    according to the technology switch you select all device models will be altered. the name of the switch differs from foundry to foundry. Usually these are: ff-> fast ss-> slow fs->fast slow sf-. slow fast You show find in the technology forder a file that contain an index of the models used in...
  11. C

    Process Variation simulation

    use corner models in you simulation. you can do this by seleting from ADE SETUP->model libraries an here select the corner switch.
  12. C

    How to update a symbol to add an extra pin in Cadence?

    Re: Symbol update in cadence yibinhsieh gave you the best answere. you have to be carefull when you update the symbol because adding pins by hand on a previously created symbol can cause problems when you export schematics in cdl format and then use this format for verifications. be very...
  13. C

    Common Mode Feed Back??

    Also a good book where you will find a chapter dedicated to CMFB is Gray and Meyer 4th edition. I think is the best reference for trying to understand this type of circuit.
  14. C

    DC analysis in Cadence

    the models are corect.I've seen these negative cap values in several design kits.
  15. C

    How to export the wave form from Cadence ?

    In order to export a waveform from cadence fisrt you have to select the format in which you want this waveform to be saved. This is done by using the -f <format> option in the ADE->Setup->Environment usrcmdline. for format I used "psfascii" but you have other formats available (use spectre -h...
See more

Part and Inventory Search

Back
Top