Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by arbabar

  1. A

    TCP/IP Frame Vs packets

    in tcp/Ip there are two layer data link layer and ip layer both contains data in their field (payload). in case of Data link layer it is 1500bytes. without header in case of ip datagram it is 65535bytes. including header suppose we are connected with network so how my computer...
  2. A

    NAT Layman Question from NETwork Engineers

    ok cool FVM thankyou for ur time is there any limitation ? ? how much subnets of /24 can we translate to one public ip? if router translate both address and ports then why we differentiate them separately as name NAT (just address translation) PAT(port Translation...
  3. A

    NAT Layman Question from NETwork Engineers

    HEllo Guys how are you and whats up.. i have a general question about nat lets say my public ip address from the isp is 116.52.52.1./32 this ip is provide by My ISP lets say my internet is 12Mbps and My company Manager tell me to configure a network 192.168.0.1/24 with 192.168.0.1/32 My...
  4. A

    How to compute the convolution of following fn

    There are two functions * is convolution sign between them look at it again
  5. A

    How to compute the convolution of following fn

    I am preparing for test so if you know how to solve it... Do it... I just tick the option by checking the answer from back of the chapter...
  6. A

    How to compute the convolution of following fn

    Y[n]=(-1)^n * 2^n u[2n+1] Please solve it and share it. http://obrazki.elektroda.pl/8516025300_1456658135.html"
  7. A

    understanding LLVD and BLVD in BTS

    what is the purpose of DC output circuit breakers (BLVD) Battery Low Voltage Disconnect and (LLVD) Load Low Voltage Disconnect. like if the voltage is -48 from the rectifier it is output DC voltage... how can we understand BLVD and LLVD in this scenario? either dc voltage is decrease to -48...
  8. A

    LPU(light protection unit) Basic question

    how light protection unit block million of amperes current produced due to lightning ? is it Burn it self while protecting the telecom equipment like bts how can it handle million of amperes current? what alarm will generate if our site is victim of lightning ? thankyou
  9. A

    Advantage and Disadvantage of DTMF In Telephony

    HI what is the advantage and disadvantage of DTMF in Tone dialing? what is it difference with the Latest ISDN?
  10. A

    How to place thermal vias in PCB

    heat sinker is independent of pcb design circuit........
  11. A

    What after PIC16 series?

    go for 16 bit mcu
  12. A

    how 8-bit pic 16f877 deal with alu data more than 8-bit

    hi i am newin pic which plat form is batter for me to understand and learn pic programming assembly language or pic c? and second is that i m learning about assemble i learned that w register Work-register is 8 bit...... maximum number in it is FFH which is equal to 255 in decimal what if...
  13. A

    0-30 v dealing with adc of pic16f877

    thankyou jayanth.devarayanadurge how do u select these values hit and trial or some formula....
  14. A

    0-30 v dealing with adc of pic16f877

    hello, i want solution of my problem kindly suggest me i m looking for it my sensor output voltage ranged 0-30v but controller works on 0-5v so i use potential divider circuit and limited the voltage to 0-2.5v as r2=430k and r1=4.7M formula = Vout={r2/(r1+r2)}*Vtotal...
  15. A

    [MOVED] simple calculation problem

    5mv(.005v)= 1 adc Value .00083v =? adc value tel me the formula for this thankyou
See more

Part and Inventory Search

Back
Top