Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Anonymous_Ricky

  1. A

    Special characters in Capture CI 16.6

    Hi, Thanks, I tried it but without any success.
  2. A

    Special characters in Capture CI 16.6

    how to use Ω in orcad capture cis and in Allegro (V16.6)
  3. A

    PCB ordering question from a newbie

    Hi, You can just give PCB thickness, copper layer thickness and number of layers in your PCB fabrication drawing. Let PCB manufacturer decide preperg thickness, if your board does not require high speed routing and impedance control. Regards
  4. A

    PCB Netlist create in orcad16.6

    Hi, You can select "ignore fixed property" tab while importing netlist. Regards
  5. A

    Gerber File viewer and checking CAM

    Hi, You can try DFM Now! V8 by Numerical Innovations, Inc. Regards
  6. A

    Device_type property in Cadence Allegro

    If someone has something on this please help me.
  7. A

    Device_type property in Cadence Allegro

    I was going through the compoenent properties in Allegro where I noticed that in device type same components has two differnet device type values though part has source package , pcb footprint and value as same. Case 1 CAPACITOR_CAPC1005_0H60N_100PF_ CAPACITOR_CAPC1005_0H60N_100PF Case 2...
  8. A

    Effects of reducing copper thicklness from 1 oz to 1/2 oz

    Hi Klaus, I got your point I should have been more specific with my application. I am designing PCB for Automotives and it is not very high frequency <100MHz. Thanks smijesh
  9. A

    Effects of reducing copper thicklness from 1 oz to 1/2 oz

    Hi Klaus, Thanks for reply but any of your response was of no help.
  10. A

    Effects of reducing copper thicklness from 1 oz to 1/2 oz

    Hi All, we have to reduce cost of one our PCB. It is 4 layer PCb with 1oz stackup. we are planning to make it in 1/2 oz but our concern are (Power is not an issue as it is manageable): 1. how much cost effective will it be? 2. will there be any EMC issues due to this? I am unable to get any...
  11. A

    altium errors (net xxx only have one pin)

    Re: altium error ( net xxx only have one pin) These are single pin nets, means that these conncetions starts from U1 pins but donot connect to any other pin. If these are deliberate then you can ignore them.
  12. A

    Diffrent colors to shapes

    You have to assign colors to net rather then to components by using this "Color" tab. You can select different colors for each nets from "Option" window. For 3D view check View>>Dynaimc Layer Visibility in 3D viewer
  13. A

    [SOLVED] Allegro PCB Editor (Flip horizontal and vertical)

    You have provided drill holes in component libray or on PCB. If it is in PCB then you have to select "user defiend pick-up points" while flipping the component. I would suggest to put drill holes in component itself if you have not done it.
  14. A

    Errors in generating netlist in Cadence Capture CIS -> Allegro, what to do?

    your BRD file is locked or still being used by user "vpdo" get it unlocked then re-import the netlist.
  15. A

    0.50 mm pitch QFPs at 2 oz copper thickness

    Hi Marce, Thanks for your reply My other concern is, could there be any chance of pads getting shorted due to 0.50 mm fine pitch and 2Oz copper thickness. Ricky
See more

Part and Inventory Search

Back
Top