Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

How to Flash Atmel ATTINY 2313 IC? Which Programmer:

Status
Not open for further replies.

JRRED

Newbie level 4
Joined
Apr 6, 2007
Messages
6
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,323
atmel 2313

Hello All,

This is great forum to be a member. I am very newbie and I need help on how to flash ATTINY 2313 Atmel IC? Which programmer do I use? Do any programmer out there to buy and if there is schematics to build my own programmer?

Sorry for few questions,
Thnx..
JR
 

attiny2313 flash

Hi,

There are lots of programmers for this chip. The determining factor of which to build is whether you have a dedicated parallel port available or not. USB to parallel port adapters will not work. You need a parallel port on the motherboard. If so, then

http://www.scienceprog.com/avr-isp/

is one example of a simple DYI programmer. There are lots of other variations and alternative circuits. BASCOM BASIC software can run some programmers. Avrdude from WINAVR can also be configured for a lot of different parallel port programmers. Another programming software is PonyProg. Research these and you will find schematics for the hardware.

If you only have available serial ports, then most likely you will have to purchase a programmer. The reason is, the programmer requires a programmed microcontroller as one of this components. So, it is like the chicken and the egg. You need the programmed part to build the programmer and you need a programmer to program the part.
 

atmel attiny programmer

Hi Banjo,

Thanks for the reply, and thanks for the link.
I did check that link and I do have Parallel Port but I do have few exactly following IC when I read from top of these IC.

ATMEL 0606
ATTINY2313V-10PU

It has total of 20 LEGS IC. and its DIP but not surface mount.

I also has two COM1 and COM2 Port.

How do I make 20 PINS programmer?

Please help me to make this programmer.

Thnx for your help buddy..
JR
 

atmel 2313 programmer

i use a program called pony prog to flash the attiny2313. it uses it's own programer that you can build at home for about $10. it's a serial programer. i forgot the website, but i'm pretty sure if you just google it you'll find it. good luck.
 


atmel flash

there will be a 20 dip socket on the programmer, you just put your t2313 into it, then when you're done programming, just pull it out, and put it into what ever you're going to use it in. i suggest using a ic puller to pull it, but if you don't have one just pry it out slowly with something flat like an xacto. it's kind of hard to pull it out of the socket by hand and not bend the pins.

oh by the way there are 2 versions of the programmer. try to find the one that's a single sided pcb, and it's a single board. don't get the one that uses all the doogles.

Added after 20 minutes:

alright, since i'm bored and had nothing to do. i decided to help you with some of the leg work.
o.k. first go here to download the pcb image:
h**p://www.electronics-lab.com/projects/mcu/009/index.html
download the pdf file. and the use the last image. that's the bottom side of the pcb. the fist image is the topside, and the middle one is the silkscreen.
then go here to download the latest version:
h**p://www.lancos.com/
 

flash attiny2313

check here. you will find plenty of programmers for AVR microcontrollers

h**p://www.avrfreaks.net/index.php?module=FreaksTools&func=viewTools&q=&category_id=57
 

attiny bascom

Hi Jimmy,

Thanks for your two links, its really help me to build myself.

However, I do have few questions before start builiding.

1. Do I need following IC before start flashing my ATTINY2313?

U1 ?
U2 I needed for sure.
U3 ?
U4 ?
U5 ?
U6 ?

Rest of those parts I do need but I have above is in questions.

I really appreciated for your time and help.

Thnx,
JR
 

programming atmel attiny2313

Any advice?
 

www.atmel 89s8252 ic programer in n c r

Hi Jimmy,

Thanks for your two links, its really help me to build myself.

However, I do have few questions before start builiding.

1. Do I need following IC before start flashing my ATTINY2313?

U1 ?
U2 I needed for sure.
U3 ?
U4 ?
U5 ?
U6 ?

Rest of those parts I do need but I have above is in questions.

I really appreciated for your time and help.

Thnx,
JR
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top