How to output a line/dot to a VGA monitor in VHDL?

hi,

anyone know how to output a line/dot to a VGA monitor? i'm new to VHDL. i'm using a @ltera UP2 board. i had found a sample program(codes are pasted below), it's a program for VGA synchronization. But how do i make use of this program to diaplay a dot or line? Because my project actually required to input a 8 bit signal through adc, after converting it to a digital signal, i need to output it to the monitor. It's acts just like a oscilloscope. Can anyone kindly help me ? Thanks alot!!!!!

Eg:

--Generate Horizontal Sync Signal using H_count
IF (h_count <= 755) AND (h_count >= 659) THEN
horiz_sync <= '0';
ELSE
horiz_sync <= '1';
END IF;

Can anyone please kindly help me ? Thanks a lot !!!!!
Regards,
65656565

library IEEE;
use IEEE.STD_LOGIC_1164.all;
use IEEE.STD_LOGIC_ARITH.all;
use IEEE.STD_LOGIC_UNSIGNED.all;

ENTITY VGA_SYNC IS
PORT( clock_25Mhz, red, green, blue : IN STD_LOGIC;
red_out, green_out, blue_out, horiz_sync_out, vert_sync_out : OUT STD_LOGIC;
pixel_row, pixel_column: OUT STD_LOGIC_VECTOR(9 DOWNTO 0));
END VGA_SYNC;
ARCHITECTURE a OF VGA_SYNC IS
SIGNAL horiz_sync, vert_sync : STD_LOGIC;
SIGNAL video_on, video_on_v, video_on_h : STD_LOGIC;
SIGNAL h_count, v_count :STD_LOGIC_VECTOR(9 DOWNTO 0);

BEGIN

-- video_on is high only when RGB data is displayed
video_on <= video_on_H AND video_on_V;



PROCESS
BEGIN
WAIT UNTIL(clock_25Mhz'EVENT) AND (clock_25Mhz='1');

--Generate Horizontal and Vertical Timing Signals for Video Signal
-- H_count counts pixels (640 + extra time for sync signals)
--
-- Horiz_sync ------------------------------------__________--------
-- H_count 0 640 659 755 799
--
IF (h_count = 799) THEN
h_count <= "0000000000";
ELSE
h_count <= h_count + 1;
END IF;

--Generate Horizontal Sync Signal using H_count
IF (h_count <= 755) AND (h_count >= 659) THEN
horiz_sync <= '0';
ELSE
horiz_sync <= '1';
END IF;

--V_count counts rows of pixels (480 + extra time for sync signals)
--
-- Vert_sync -----------------------------------------------_______------------
-- V_count 0 480 493-494 524
--
IF (v_count >= 524) AND (h_count >= 699) THEN
v_count <= "0000000000";
ELSIF (h_count = 699) THEN
v_count <= v_count + 1;
END IF;

-- Generate Vertical Sync Signal using V_count
IF (v_count <= 494) AND (v_count >= 493) THEN
vert_sync <= '0';
ELSE
vert_sync <= '1';
END IF;

-- Generate Video on Screen Signals for Pixel Data
IF (h_count <= 639) THEN
video_on_h <= '1';
pixel_column <= h_count;
ELSE
video_on_h <= '0';
END IF;

IF (v_count <= 479) THEN
video_on_v <= '1';
pixel_row <= v_count;
ELSE
video_on_v <= '0';
END IF;

-- Put all video signals through DFFs to elminate any delays that cause a blurry image
red_out <= red AND video_on;
green_out <= green AND video_on;
blue_out <= blue AND video_on;
horiz_sync_out <= horiz_sync;
vert_sync_out <= vert_sync;

END PROCESS;
END a;

Re: HELP needed!!!!

Best way is you try out XR16 processor with VGA controller. You can get
more info about it @ www.fpgacpu.org.