Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi there.
I have an old video chip which is generating one signal as sync+luma and another with color which are feed into an RF modulator to generate a composite output signal. My goal is to bypass the Rf modulator take those two signals and generate a VGA signal or HDMi. Is it doable ? Thank you.
Thanks for the information. I ordered this one for ttl:
**broken link removed**
Regarding the 3.3 voltage any suggestion for something which fits to a breadboard?
;)
Thanks
Hi Thanks for the answer . I did not completly get it.
RS232 PL2303HX 1m Z54 this is a cable with 5V as Vcc all i need to do is dropping in somehow to 3.3V. What about RX and Tx? Is any circuit example I can refer to connect the module to a PC using the cable below?
Hi guys.
I guess I am close the solution but I would like to have your confirmation.
I bougth a usb-rs232 cable:
RS232 PL2303HX 1m Z54
This cable has a supply of 5V when connected to a PC. I want to test a wifi module (ESP8266). I understood that I need to drop the voltage to 3.3 probalby...
Hi
I am using ISES for creating a PBC. I have few question:
1. What If I don't have a component in the library and I want to create the PCB?
2. Can you suggest guidance/resources/book about PBC?
Thanks
Thanks.
1. How to interface RN171 to a PIC
2. When 1 is completed are there any limitation compared with OpenPicus? If I understood correctly
OpenPicus doesn't have an onboard TCP stack and can be used as http server ( I need to connect to the board from remote computer so I need to board...
Hi
I have created a board based on PIC15F876A running a finite state machine. I want to add a wifi module so that I can read/write command to this board via HTTP. I checked online several modules:
RN131
OpenPicus
CC3000
GA1000 Wi-Fi
EasyWiFi Board
Any other suggestion?
Can you also please...
Hi.
I develpoed a board with PIC16F. Now I need to add a programmable module which convert serial to ethernet. The module need to be connected to the PIC via RS232 line (tx and rx). Because I would like to us those line also for reading other pheriperal how I can do that?
Shoul I add a mux...
So at this point...an equivalent board you fill confident to suggest which works with MPLAB?
Yes I have been using Hitech, the free version. I am interested in ethernet communication.
I see but you know sometime i see other components in other the schematics like resistors and capacitors that are not shown
in the datasheets which seem to be very logical diagram. Because of this sometime i missed some of them
and the board didnt' work.
Hi. You are very active today answering my question.
Thanks you very much for your help.
The manual says EasyPIC PRO™ v7 is equipped with RJ-12 connector. In your opinion does make sense to buy such board and use it without their compiler?
This is the support reply:
EasyPIC PRO v7 has...
Wanted to create something like this:
**broken link removed**
So the PIC i already have is a PIC18FXXX.
So an 74HCT08 should work just fine. By the way I don't see on farnell enc28j60.
How I should interface the 74HCT08 between PIC and ENC28J60. Any schematic?
Thanks a lot.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
