Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by Thayas

  1. T

    Place the webcam on Stepper Motor

    Hi All, Anyone can tell me hw can i place the wecam on stepper motor? I want to rotate the wecam according to the stepper motor's rotation. Regards Thaya
  2. T

    Help me rotate a unipolar stepper motor in small angles

    Re: Micro stepping Ya..i culd rotate the stepper motot at 90 degrees.now i want to control it small angles(7.5 degrees)
  3. T

    Help me rotate a unipolar stepper motor in small angles

    Hi all.. Im using six wire unipolar stepper motor(7.5degrees). im able to rotate in half step mode.. Now i want to rotate in small angles(7.5). I hav no idea..Plc anyone can guide me.. Regards Thaya
  4. T

    Do we have to configure the Ossilater Type before burn

    We use PICSTART Plus. I jst checked whether my pic work correctly or not by flashing LEDs. But wn i connect both capcitor(33pf) to ground ,it did nt work.if i remove,one capcitor output from grond.it works.i used 4mhz crystal.Plc help me... Wn i design this circuit in PROTEUS,It works fine...
  5. T

    Do we have to configure the Ossilater Type before burn

    we have encounterd a problem when we tried to burn the PIC64F84A! We used a ossilaror called FT 4MHz. PIC doesnt give correct out put! How can slove this problem? [/size]
  6. T

    Help me fix this code for rotating 6 wire unipolar stepper motor

    Re: Please help me..... Yes,That is typing mistake. My target processor is (PIC)16F84A.
  7. T

    Help me fix this code for rotating 6 wire unipolar stepper motor

    Re: Please help me..... Yes,Thats correct. I used ULN2003A IC. My prob is "Pic did not give any output from RB1,RB2. Only RB0 and RB1 gives the output. what's the error in the coding.. But it's working proberly in PROTEUS simulator. Thanks Regards Thaya
  8. T

    Help me fix this code for rotating 6 wire unipolar stepper motor

    Hey all, I got a code to rotate 6 wire unipolar stepper motor from the internet.. It works fine in PROTEUS Simulator(All four ( RBO,RB1,RB2,RB3) pins gives output) When i tried it in bread board.Only two pins(RB0,RB1) give the out put.I did not get any signals from RB2,RB3. coding LIST...
  9. T

    Unipolar Stepper Motor vire identification..

    identifying coil of unipolar stepper motor Thanks amrstaha.... Regards Thaya
  10. T

    Unipolar Stepper Motor vire identification..

    stepper motor wire identification Hi all, Ive got a 6wire unipolar stepper motor. Infor.. VOLT 24V COIL 22Ohm STEP 7.5 (Tokyo Electric,CO.,LTD,JAPAN) It has six wires.reds-2,yelow,orange,brown&black. can any one tell me which wires should connect to power..? Thank u Regards Thaya
  11. T

    Serial Port Programming in C

    Hi all, i want to send signals to MC(PIC1684A) through the serial port using c. (only need three pins to send data) i have developed interface in java. can any one help me... Thank u Regrds Thaya
  12. T

    PCB design for PIC Development kit (PIC16F84A)

    can u give me that link?
  13. T

    PCB design for PIC Development kit (PIC16F84A)

    I need circuit design only. Friends, I build a simple circuit to test PIC16F84A. but i did not get any output prom pic pins. i connect VDD,MCLR to 5V.VSS to ground pin,use 4MHZ crystal,two 22pf cap to OSC1,OSC2.aND Write a simple code to get a signal from RB1.its work fine in PROTEUS...
  14. T

    PCB design for PIC Development kit (PIC16F84A)

    pic16f84 development Hi all, I want to build a development kit for PIC16F84A. Im now searching for PCB design. could any one help me.... Thanks Regards Thaya
See more

Part and Inventory Search

Back
Top