Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Better check the mother Electronics Link from where original text resides.
27MHz Links
Look, This Page 2 have the Cordless bell workings. But the first and third page gives all related information.
Thanks
A simple try.
Just change one pair of 32KHz with other freq. nearer to 32KHz. It will be selective to that audio noise. Carrier will be same.
Experts comments needed.
Thanks
Use a Medium wave antenna coil, with ferrite rod. In absence, take 8mm ferrite rod, Large coil 32SWG Super enameled 80 turn. Small feedback coil 8 turn. Resistor-100K-10K Ohm, feedback capacitor 220pf. Connect 220pf Capacitor parallel with PVC 2J Gang (Variable capacitor) across +Vcc and...
It simply chops the sine wave and cuts the 0-30 volt by making off the current. The analog measuring instrument will measure false reading ashuming sine wave current and taking RMS. But this distorted waveform can generate harmonics and reduce the lifes of the electrical equipments specoally...
Resistor tolerance
Tolerance matters in the precision biasing like 431 or like that rest can be designed with 10% tolerance with measuring. a 1% Change even can change 2 volt output in SMPSs.. In ballast current measuring resistor even destroy the lamp in 50% life too or increased life with...
As per my knowledge, APC inverter , checked by me can take more than 80% of rated load safely. Moreover, The charging circuit is really good. Not be able to charge like 70/90/120/150/180 AH Battery but surely can charge upto 24AH Safely.
I Recomended no need for separate charging if not large...
Why not Simple transistorised circuit if not load is too high? A simple circuit with astable multivivrator with buffer and Diode Capacitor half wave rectified voltage doubler. Reduce the Capacitors in the astable multivibrator to increase frequency.
Increasing load current will have to replace...
Just Open your PS and adjust the biasing in the feedback circuit in the 431 IC. If require, just read the TL431 Datasheet from Internet. Then fix it at 12 Volt. Make 5 volt with any linear regulator like 7805 if it';s load requirement not too much (I Think). Adjusting 431 biasing is the best...
Ballast Design
Just reverse engineer a few similar type, you see, all schematics are basically same(Not IC Based, I Recomend Transistor like 13003 or 13005). Just consider measure frequency and inductance of inductor. Now Recalculaate your early FL Ballast Inductor and wind with new data.
you...
Basic core design require your frequency, relative permiability and you got area product. Then select the core with that area product. (Ref: Fairchild Application Note 4140 at www.fairchildsemi.com).
However a basic crude table followed by the designers and here is that. They all consider the...
Hi,
I have thought and gives here schematics for LED Driver/Ballast (SwitchMode).
The concept is the following.
1. Transistor starts conducts and Fire SCR (PNP+NPN pair) till curremt limit reaches.
2. The SCR Draws base voltage down to near zero (Switch off & current through Schottky...
High Pressure Sodium has more efficacy than normal fluroscent. But a comperative study is found here.
https://sites.google.com/site/kalyanprodhan2/LEDvsHPS.pdf
with pictures here.
https://sites.google.com/site/kalyanprodhan2/ledprojectsatbesu
I Think the main problem in Cheap LED Lamp is it's...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
