problem wtih reading and wirting cs5460 with at89c52

hello experts,
i here with atached part of code which is used for getting register values , but the problem is i'm not getting any values . im looking a guidance for read/write cs5460 with at89c52, software which im using is keil version.

warm regards,
selvam, bangalore.


cmd_5460(0xff); //nop
delay(1000);
cmd_5460(0xff); //nop
delay(1000);
cmd_5460(0xff); //nop
delay(1000);
cmd_5460(0xfe); //nop
write_5460(0x4a000012); //writing cycle count reg; with value of 18d
delay(1000);
write_5460(0x5e000001); //writing status register; with value of 1;
delay(1000);
write_5460(0x40000004);//writing config reg wih value of 4 for clock divider;
delay(1000);
write_5460(0x78000008); //writing control register for synchronize with adc clock;
delay(1000);
write_5460(0x74800000); //writing mask registr o mask all bits except drdy bit;


cmd_5460(0xe8);// start conersiion for continuous computation cycle

delay(1000);
cmd_5460(0x16);// read irms register
read_5460();


void cmd_5460(unsigned char cmd)
{
unsigned char i=8;
while(i>0)
{

if(cmd & 0x80)
{
sdi_5460=1;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);

}
else
{
sdi_5460=0;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);
}
i--;
cmd=cmd << 1;

}
}


unsigned long read_5460(void)
{
unsigned char i,j=0;
unsigned long temp;// temp is used to store read value
temp=0;
while(j<3)
{
i=7;
sdi_5460=1;
while(i>0)
{
temp=temp<<1;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);

if(sdo_5460==1)
{
temp=temp|0x00000001;
}

i=i-1;
}
sdi_5460=0; /writing zero at eighth bit to be read.
temp = temp << 1;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);
if(sdo_5460==1)
{
temp = temp|0x00000001;
}
j=j+1;

}
if(temp==0)
{
P2=disp1;
P0=1;
}

else
{
P2=disp2;
P0=1;
}

return(temp);

}


void delay(unsigned int q)
{

while(q>=1)
{
q=q-1;
}

}


void write_5460(unsigned long reg_value)
{
unsigned char k=32;
while(k>=1)
{
if (reg_value & 0x80000000)
{
sdi_5460=1;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);
}
else
{
sdi_5460=0;
sclk_5460=0; //clk applying
delay(1000);
sclk_5460=1;
delay(1000);
}
reg_value = reg_value << 1;
k=k-1;

}

}