JDM Programmer Advance Hardware

Status
Not open for further replies.

when i use winpic .its result as

Code: 
[CODE]Programming...
Erasing ("bulk" or "chip") ...
Programming and Verifying CODE, 0x000000..0x0003FF
Verify Error: 000000: read 003FFF, wanted 003000
Verify Error: 000001: read 003FFF, wanted 00008A
Verify Error: 000002: read 003FFF, wanted 00283C
Verify Error: 000003: read 003FFF, wanted 000000
Verify Error: 000004: read 003FFF, wanted 001A83
Verify Error: 000005: read 003FFF, wanted 00280A
Verify Error: 000006: read 003FFF, wanted 0000A5
Verify Error: 000007: read 003FFF, wanted 000E03
Verify Error: 000008: read 003FFF, wanted 0000A6
Verify Error: 000009: read 003FFF, wanted 00280F
Verify Error: 00000A: read 003FFF, wanted 001283
Verify Error: 00000B: read 003FFF, wanted 0000A5
Verify Error: 00000C: read 003FFF, wanted 000E03
Verify Error: 00000D: read 003FFF, wanted 0000A6
Verify Error: 00000E: read 003FFF, wanted 0014A6
Verify Error: 00000F: read 003FFF, wanted 00080A
Verify Error: 000010: read 003FFF, wanted 0000AD
Programming aborted after 17 errors.
Programming CONFIG, 0x002000..0x002007
Verify Error: 002007: read 003FFF, wanted 003104
ERROR: Programming FAILED !
[/CODE]
 


there are lot of possibilities, first did you put the chip in right place and right direction on ZIF socket also test that is VCC and VDD present when you power on the programmer, also check is VVP comes on at MCLR pin of 16F676 when you press program button, if all OK then chip is defective.

verified your hardware with schematic for connection brake

Fragrance
 


I didn't find any attatchment,any body can tell me where is the schematic or circuit diagram???!!!!!!!
 

That's strange, it's at the end of the post you quoted. I've copied it here:
 

No, you do not need to program a PIC for this programmer to work.

That is the best thing about JDM-type programmers. They do not use a PIC to control the programmer, just some basic logic chips. All of the control is done by the software on the PC.

It's an ideal "First" programmer to make yourself.
 


thank you very much FoxyRick!!!!!
now I'm very happy ,bcoz I don't need to buy any pickit for programming any pic uC.
 

Dear sir, your job is excelent. you have attached JDM final updated. In that PCB, schematics are not open. If You don't mind, kindly publish those once again in PDF formate. Thanks
 

Ranganathan Ramaswamee said:
Dear sir, your job is excelent. you have attached JDM final updated. In that PCB, schematics are not open. If You don't mind, kindly publish those once again in PDF formate. Thanks
Click to expand...

here you go

Fragrance
 

Attachments

  • JDM Advance all PDF.rar
    96.2 KB · Views: 197
Reactions: qrp

    Q

    qrp

    Points: 2
    Helpful Answer Positive Rating
Thanks 4ur programer.hw wil i insert 8 & 18 pin ic's into the zif socket.thanks
 

The diagram in the first post of this thread shows where to place the MCU. The line indicates where to insert pin 1.
 

@fragnance.thanks for your circuit.Please why did u conect capacitor c11 negative terminal to +5v and c12 positive to gnd?how corect is it?pls xplain.i want to program pic16f84.how wil i insert pic16f84a into d socket?wher wil i start to insert pin 1 of the pic16f84? i've never programmed b4.my laptop serial port has a male conector bt in page3 u showed female to female conection.thanks
 
Last edited:

Typing in full English would help - there is no need for such abbreviations - they make your question difficult to read and thus less likely to elicit any help.
 
Hi All,

Can anyone tell me if this circuit really needs a 16V DC supply. I have a 15V dc supply and also have a 13V DC supply, I know the current doesnt matter as the circuit will draw whatever current it needs but the voltage seems a bit high to me.

Thanks
ikhan42
 

Hi Fragrance ,
I recently came across a universal Zif designed by you by the name PPICKIT2 UIVERSAL ZIF FINAL . The older version seems to have more options to Different type of PIC for example 20 pin PIC. I want to Know is there any other advantage like more PIC compatability in the New Zif connector configuration posted in this thead JDM Programmer Advance Hardware. waiting for your reply.
regards ani
 


pikkit2 zif socket design have one option more then JDM it can program 10f series as well

Fragrance
 

Fragrance said:
pikkit2 zif socket design have one option more then JDM it can program 10f series as well

Fragrance
Click to expand...
So if you integrate PICKIT2 Zif socket with this new JDM Programmer Advance Hardware it will make a wonderfull combination. Is it possible to use PICKIT2 Zif socket for PIC 18F4550 and 18F4455
regards ani
 

picgak said:
So if you integrate PICKIT2 Zif socket with this new JDM Programmer Advance Hardware it will make a wonderfull combination. Is it possible to use PICKIT2 Zif socket for PIC 18F4550 and 18F4455
regards ani
Click to expand...

yes you can used

Fragrance
 
Reactions: picgak

    picgak

    Points: 2
    Helpful Answer Positive Rating
Hi Fragrance ,
I was checking the pin connections of your PPICKIT2 UIVERSAL ZIF FINAL for testing , can you kindly check the connections to pin No 7,9,15,27,28 of the zif. Is it required. I did not find any connections required in that pin based on your configuration. Can you please Kindly clarify for what purpose those connections are. Thanking you
regards ani
 

Status
Not open for further replies.

Similar threads

Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…