install voltagestorm
ic*, dsmse, psd, ams and ldv Packages
setenv CDS instdir
setenv CDS_INSTALL_DIR $CDS/tools/dfII
setenv LD_LIBRARY_PATH "/usr/openwin/lib:/usr/dt/:/usr/dt/lib:$CDS/tools/lib:$CDS/tools/verilog/lib:/usr/X11/lib:/usr/lib:/usr/X11R5/lib:$CDS/tools/leapfrog/lib"
setenv SHLIB_PATH /usr/lib:/lib:/usr/lib/X11:$CDS/tools/lib:$CDS/tools/verilog/lib:$CDS/tools/leapfrog/lib
setenv CDS_LIC_FILE $CDS/share/license/license.dat
setenv CDS_Netlisting_Mode Analog
setenv PATH "$CDS/tools/bin:$CDS/tools/dfII/bin:$CDS/tools/leapfrog/bin:$CDS/tools/dracula/bin:$CDS/tools/dsm/bin:$CDS/tools/specctra/bin:$CDS/tools/pcb/bin:${PATH}"
setenv CLS_CDSD_COMPATIBILITY_LOCKING NO
setenv DD_DONT_DO_OS_LOCKS SET
Note: If there are subpackages under $CDS/tools that you need in addition to dfII, leapfrog, etc., add them to the PATH setting above. Similarly, you can remove packages you don't need (e.g. remove leapfrog, dracula and specctra if just setting up silicon ensemble).
You may have to set NC_INST_DIR to $CDS_INSTALL_DIR for AMS.
Note: If running verilog on Red Hat 9, set LD_ASSUME_KERNEL as follows to get around the GLIBC_2.0 error:.
setenv LD_ASSUME_KERNEL 2.4.1
Cadence Chip-assembly router/Virtuoso Custom Router (aka IC Craftsman) Package
setenv CDS instdir
setenv CDS_LIC_FILE $CDS/share/license/license.dat
setenv PATH "$CDS/tools/bin:$CDS/tools/iccraft/bin:$CDS/tools/iccraft/gds_if/bin:$CDS/tools/iccraft/lefdef_if/bin:${PATH}"
SPR (Ambit) Package
setenv CDS_LIC_FILE instdir/license.dat
setenv PATH "instdir/BuildGates/current/bin:${PATH}"
Assura Package
setenv ASSURAHOME instdir
setenv CDS_LIC_FILE $ASSURAHOME/share/license/license.dat
setenv PATH "$ASSURAHOME/tools/bin:$ASSURAHOME/tools/assura/bin:${PATH}"
SEV Package (VoltageStorm, Fire & Ice)
setenv SIMPLEX_HOME instdir
setenv LM_LICENSE_FILE $SIMPLEX_HOME/share/license/license.dat
setenv PATH "$SIMPLEX_HOME/bin:${PATH}"
TSI (SignalStorm/Celtic/Pacific) Package
setenv TSIHOME instdir
setenv CDS_LIC_FILE $TSIHOME/share/license/license.dat
set path=($TSIHOME/tools/bin $path)
setenv TCL_LIBRARY $TSIHOME/tools/sndc/lib/sndc/tcllib
VSDE Package
Note: setup environment for ic package and add the following:
setenv ACV_ROOT instdir/tools/acv
set path=($ACV_ROOT/bin $path)
setenv LD_ASSUME_KERNEL 2.4.1 (Linux only)
SNA Package
source instdir/tools/seismic/CSHRC50
setenv CDS_LIC_FILE instdir/share/license/license.dat
NeoCell Package
setenv CDS_LIC_FILE instdir/share/license/license.dat
set path=(instdir/tools/NeoCell/bin $path)
Note: you will also have to set up your environment to run the IC package