[SOLVED] PIC GIPO functionality problem

Code C - [expand]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
#include "p18f45k20.h"
#pragma config PWRT = OFF, BOREN = SBORDIS, BORV = 30                       // CONFIG2L
void main (void)
{
  
unsigned char data ;
  TRISC = 0b11111111;
  TRISD = 0b00000000;
  TRISA = 0b11111111;
 
 LATDbits.LATD0 = 0; // for led bit
 data =  PORTAbits.RA5 ;
if ( PORTAbits.RA5 == 1 )
 LATDbits.LATD0 = 1;
  /* Light the LEDs */
 
  while (1)
    ;
}

Code C - [expand]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
#pragma config WDTEN = OFF, WDTPS = 32768 // CONFIG2H
#include <p18lf24k22.h>
#include "clock.h"
#include "Uart_1.h"
#include <spi.h>
 
#define DEBUG 1
 
#define HIGH 1
#define LOW 0
 
#define LED LATAbits.LATA1
#define TUNE_READY LATAbits.LATA0
 
#define D_POT_1 LATCbits.LATC2
#define D_POT_2 LATCbits.LATC1
#define D_POT_3 LATCbits.LATC0
 
#define RF_Sw_A1 LATAbits.LATA4
#define RF_Sw_A2 LATAbits.LATA5
#define RF_Sw_B1 LATAbits.LATA6
#define RF_Sw_B2 LATAbits.LATA7
 
 
unsigned char SPI_Recv[10];
 
void main(void) {
    
    unsigned char i,channel = 0, data = 0 ,w , temp;
    CloseSPI2();
for(w=0;w<25;w++)
SPI_Recv[w]=0;
 
    TRISAbits.TRISA1 = 0; //Makes 1st bit of PORTA Output for LED
 
    TRISBbits.TRISB0 = 1;
    TRISBbits.TRISB1 = 1;
    TRISBbits.TRISB2 = 1;
LED = HIGH ;
while(1)
{
temp = PORTBbits.RB0 ;
channel = PORTAbits.RA1 ;
data = PORTBbits.RB2 ;
}
 
    if(clock_configure(16))     //set the CPU CLOCK to 16Mhz
    {
        for(i=3; i>1; i--)
        {
            //Blinking Led twice to indicate clock config Done/
            LED = LOW; //Makes 1st bit of PORTA at Logic Low //RED_LED off
            delay();
            LED = HIGH; //Makes 1st bit of PORTA at Logic High //RED_LED on
            delay();        
    }
}
OpenSPI2(SLV_SSON,MODE_00,SMPEND);
for(i=0;i<100;i++);
temp = ReadSPI2();
 
while(1)
{
       /* while (!DataRdySPI2());
    LED = LOW;
       getsSPI2(SPI_Recv,10);
 
       while (!DataRdySPI());
       LATDbits.LATD1 = ~LATDbits.LATD1  ;
       temp = ReadSPI(); //End of program
*/
}
    CloseSPI2();
}//MAIN