Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

PTM and MOSIS process technologies

Status
Not open for further replies.
aindejeje

aindejeje

Junior Member level 2
Joined
Sep 29, 2009
Messages
21
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,283
Activity points
1,416
Help Me. Basic of PTM technology.

Hi all,

Previously i used process technologies from Mosis for my simulation.
It already has test result for every technologies.
Now im migrating to PTM model.
Im looking for minimum dimension for 90nm, 65nm, 45nm and 32nm technology.

From IBM test result (130nm), the Lmin=0.12u, and Wmin=0.16um
It there any way to determine the Wmin?

And how can i find λ, µ, and γ for PTM?

Thanks for your help!
 

Re: Help Me. Basic of PTM technology.

>From IBM test result (130nm), the Lmin=0.12u, and Wmin=0.16um. It there any way to determine the Wmin?
Yes, a simple way is to use a technology scaling model. I typically use the model presented in Digital Integrated Circuits: A Design Perspective by Rabey, Jan M (2nd edition). See table 3-8 on p.124.

Using this model for to find W for the 32nm process would give a scaling factor S =Lmin,old / Lmin,new = (130nm) / (**32nm)= 3.75
Then you can solve for Wmin,32nm = (Wmin,130nm)*(1/S) = (0.16um)/(1/3.75) = 0.0427e-06. This gives a smaller W which is what we expect.

**this value may be smaller by a few nm.
>And how can i find λ, µ, and γ for PTM?
You may apply the same technique above for some of these values but some may be only found from foundries that make those technologies. I would recommend looking through IEEE papers.

Cheers,
analogLow
 
Re: Help Me. Basic of PTM technology.

analogLow said:
>From IBM test result (130nm), the Lmin=0.12u, and Wmin=0.16um. It there any way to determine the Wmin?
Yes, a simple way is to use a technology scaling model. I typically use the model presented in Digital Integrated Circuits: A Design Perspective by Rabey, Jan M (2nd edition). See table 3-8 on p.124.

Using this model for to find W for the 32nm process would give a scaling factor S =Lmin,old / Lmin,new = (130nm) / (**32nm)= 3.75
Then you can solve for Wmin,32nm = (Wmin,130nm)*(1/S) = (0.16um)/(1/3.75) = 0.0427e-06. This gives a smaller W which is what we expect.

**this value may be smaller by a few nm.
>And how can i find λ, µ, and γ for PTM?
You may apply the same technique above for some of these values but some may be only found from foundries that make those technologies. I would recommend looking through IEEE papers.

Cheers,
analogLow
Click to expand...
Thanks for the equation and explanation.
Can you provide me specific link for IEEE papers to this issue.

erikl said:
You can also find Wmin values for 90 & 65nm processes in the MOSIS Wafer Electrical Test Data and SPICE Model Parameters sections. Also (Spice-adapted) mobility values.
Click to expand...
I found the minimum sizing (Wmin:Lmin) from IBM for:
130nm = 0.16um:0.12um
90nm = 0.12um:0.10um
65nm = :0.12um:0.06um

IMO, this is the practical value.
thanks.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top