Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

multi point & long distance rs485 half duplex

Status
Not open for further replies.
M

mohammad hassanzade

Newbie level 6
Joined
Oct 2, 2010
Messages
12
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,283
Location
tehran,iran
Activity points
1,362
hi all guys
i design a system for control a large greenhouse & i want use rs485( max485 chip) .
in this design exist:
1-1 master & 30 slave
2- distance from master to last slave is 1km
question:
1- can the max485 to this services ?(distance with this number master/slave)
2- how i can design this circuit for distance longer than 1km ? (for example 20km)
guide :
1-i don't use another system, because this system is cheap for me :razz:
2-because the rs485 used to maximum 1.2km distance help to me to amplify signal for longer distance.(for example 20km)
thanks a lot
 

2- how i can design this circuit for distance longer than 1km ? (for example 20km)
You can use another max485 as a repeater in between. It will amplify the signal after 1km. :)

guide :
1-i don't use another system, because this system is cheap for me
2-because the rs485 used to maximum 1.2km distance help to me to amplify signal for longer distance.(for example 20km)
 

thanks john
john : You can use another max485 as a repeater in between. It will amplify the signal after 1km. :)
i want found a cheap way for this issue but this proposal is good
can do you show to me this configuration ?
can do you help me for another question?
thanks
 

can do you help me for another question? Sure :)

---------- Post added at 17:28 ---------- Previous post was at 17:18 ----------

 

good
but for repeater circuit, we need control DE or RE for in/out function & for this work we need a micro controller but this way not a cheap way
how can i found a cheap way for this issue
thanks a lot for your help

---------- Post added at 22:35 ---------- Previous post was at 21:07 ----------

hi all and john
i googled for this issue & i found a circuit
this is an application notes from maxim & wrote for rs-422
please see this & reply my question
View attachment rs485-repeater.PDF
1- this circuit work carefully & correctly? (i see this & i guess this work correctly)
2- can this circuit work for rs485?
 

it's the cheapest way... to set a microcontroller with 2 max487 as a bridge.... other ways are more expensive....
 

are you sure this is cheap, what about the cost of a 1 km (I am assuming the shortest length is 1 Km) long wire, also add the maintenance that may be required from time to time, there may be some problems like rats/animals chewing wires, water getting into wires etc.
 
Depends. You can use wireless module to solve the problem. But, the module itself cost a lot.

**broken link removed**.
 

thanks a lot for your help
rs485repeater.png
i think this schematic a cheap way & really correctly.
i hope use this way for project but test this way
if failure to a good replay,i sure use a micro controller for this issue
i think attiny2313 a good micro controller that have two interrupts
i happy ,if have any proposal & give me

i'm sorry for being weak in english
with a lot thanks
mohammad hassanzade
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top