Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

H bridge mosfet driver

Status
Not open for further replies.
J

judfid

Member level 3
Joined
Feb 19, 2009
Messages
57
Helped
6
Reputation
12
Reaction score
6
Trophy points
1,288
Activity points
1,597
h bridge mosfet driver

I want chop 200v dc to 50hz sine wave.How can i do this with minimun losses.Is it possible to use SCR.I will need a sketch for illustration
 

h bridge mosfet

The question seems unrelated to the title, however it would be really difficult to achieve it by a SCR (although possible).
 
  • Like
Reactions: adung

    A

    adung

    Points: 2
    Helpful Answer Positive Rating
h bridge mosfets

thanks. But how can i achieve it with mosfet
 
  • Like
Reactions: adung

    A

    adung

    Points: 2
    Helpful Answer Positive Rating
h bridge mosfet circuit

you use as inverter with high freq pwm , then filter out high freq to leave you your nice 50Hz.

simply vary your on time sinusoidally and the moving average will be a sine.
 

h-bridge mosfet

Hi judfid,
If you want to convert 200v DC to 50 HZ sine wave, then you have to use Full Bridge Topology with 4 Mosfets. 2 Mosfets for High Side and 2 Mosfets for Low side. High side 2 Mosfets require separate power supply with Virtual Ground. For driving 4 Mosfets, you can use 2 Mosfet drivers, like IR 2110. The output from Full Bridge Circuit has to be demodulated with LC Filter to get 50 HZ sine wave. The process require lot of theoretical and practical knowledge. Thanks.
 

full bridge mosfet driver

IR2110...........OK till you go on no load.....and then when IR2110 is not switching how does the boost cap stay charged up?
 

bridge mosfet

IR2110...........OK till you go on no load.....and then when IR2110 is not switching how does the boost cap stay charged up?
Click to expand...
You have to keep a minimum low side duty cycle. But I don't see a relation to no-load condition with a PWM inverter.
 

h-bridge mosfet driver

eem2am said:
you use as inverter with high freq pwm , then filter out high freq to leave you your nice 50Hz.

simply vary your on time sinusoidally and the moving average will be a sine.
Click to expand...
lps if u can help me with a simple circuit to achieve this , I will apreciate it
 

mosfet driver

eem2am said:
IR2110...........OK till you go on no load.....and then when IR2110 is not switching how does the boost cap stay charged up?
Click to expand...

Hi,
IR2110 is a reliable high and low side driver. If some one knows the proper use of boost capacitor and also the other parameters of it in circuit, it will give wonderful service, otherwise one will have a real tough time in using it. Thanks.

Added after 8 minutes:

Hi judfid,
There is no easy sine wave Inverter system from 2oov dc. You have to have a complex Sine Table and you can do the conversion with Microcontroller or if you don't want to use Microcontroller, then with Bubba Oscillator. If you want, I could provide circuit for both the Process. Thanks.
 

mosfet h bridge

Tahmid said:
eem2am said:
IR2110...........OK till you go on no load.....and then when IR2110 is not switching how does the boost cap stay charged up?
Click to expand...

Hi,
IR2110 is a reliable high and low side driver. If some one knows the proper use of boost capacitor and also the other parameters of it in circuit, it will give wonderful service, otherwise one will have a real tough time in using it. Thanks.

Added after 8 minutes:

Hi judfid,
There is no easy sine wave Inverter system from 2oov dc. You have to have a complex Sine Table and you can do the conversion with Microcontroller or if you don't want to use Microcontroller, then with Bubba Oscillator. If you want, I could provide circuit for both the Process. Thanks.
Click to expand...
 

h-bridge circuit mosfet

can i use RC instead of LC to filter the output of H-bridge? if yes, what values of resistor and capacitor can i use as low pass filter for clean 50Hz sine-wave output? Thanks.
 

Tahmid i really need ur help

Am building an high frequency switching inverter using the tl494,and using a H bridge,

can anyone assist me on how the H bridge converts dc back into ac, i mean how do i do this, and how do i get 50hz from this, many thanks

12vdc.....tl494...push-pull mosfets....transformer...bridge rectifier...h bridge...lc filter..

what i need to know is how to switch 2 on and 2 off at same time resulting in ac 220v ,

And how do i get 50hz, if u know
what i mean

please draw this out

this is a mod-sine wave btw

many thanks
 

Re: mosfet driver

I am working on hardware implementation of h-Bridge inverter. so plz if possible, can u send me h-Bridge inverter circuit diagram.
 

Re: mosfet driver

Hi

u can find in google simple H Bridge Inverter Circuit, Get it and try to build

Thanks
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top