Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

a question about kinematics of a particle

Status
Not open for further replies.

losheungwai

Newbie level 5
Joined
Sep 14, 2008
Messages
9
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
1,337
a car decelerates on a ramp with an initial velocity of 100 km/h and final velocity of 0.

how to find the time at which the car stops and the distance traveled on the ramp given that dv/dt varies linearly from 0 to -3 m/s^2 during evry time interval of 1s????
 

ok, here it goes what i understood:

A car is climbing a ramp, with an initial velocity of 100 km/h. At every second the car suffers a deceleration which goes from 0 to -3 m/s^2 during the whole second, linearly. So the acceleration the car would suffer would be:

second 1.0 : 0 m/s^2
second 1.1 : -0.3 m/s^2
second 1.2 : -0.6 m/s^2
.
.
.
second 1.9 : -2.7 m/s^2
second 2.0 : 0 m/s^2
second 2.1 : -0.3 m/s^2
second 2.2 : -0.6 m/s^2
.
.
.
and so on...

If this is right, then here it is my solution:

First of all we have to see the whole time needed as if it were N time intervals of one whole second plus an interval of \[t_x\] seconds, this is:

\[t_{total}=n + t_x\], where n is an integer value.

So, let's se what happens in a 1 second interval:

As it is said, acceleration will vary from 0 to -3 m/s^2 linearly during the whole second, this is:

\[a = -3t = \frac{dv}{dt}\], so \[dv = -3t\, dt\]

Then:

\[\int_{v_o}^{v} dv = \int_{t_o}^{t} -3t\, dt\]

So developing the equation: \[v = v_o + \frac{3}{2}(t_o^2 - t^2)\]

and as in every interval, we take the time reference as a new one, \[t_o=0\], so:

\[v = v_o - \frac{3}{2}t^2\]

Now, as after every interval, our time \[t=1\] second, the velocity formula for the end of every interval will be: \[v = v_o - 3/2\] (remember we are working in meters and seconds). So, if we take a look at the 1 second intervals from the begining, we'll se a pattern:

\[v_o = 100 km/h = 27.7778 m/s\]
\[v_1 = v_o - \frac{3}{2} = 26.2778 m/s\]
\[v_2 = v_1 - \frac{3}{2} = 24.7778 m/s\]
...
\[v_n = v_o - \frac{3}{2}n\]

So how many 1-second intervals will we be having? Easy, \[v_n = 0 = v_o - \frac{3}{2}n\].
\[n = \frac{v_o . 2}{3} = 18.518 seconds\]

But as intervals have to be discrete (we can't have half interval, just one whole interval) we take the lowest integer: 18.

So now we know our total time will be 18 seconds plus something else which is less than a second... Now it's time to calculate that one. For that we take again the formula we calculated for an interval, but this time, the end time won't be 1 second, but an unknown variable. And this time, \[v_o\] won't be 100 km/h either, but the speed at which the car arrived at the last interval:
\[v_o = 27.77778 - \frac{3}{2}.18 = 0.77778 m/s\]

And now we also know the final velocity for the car, for what we know all variables needed, taking again the formula:

\[v = v_o + \frac{3}{2}(t_o^2 - t^2)\]

and we substitute the values:

\[ 0 = 0.77778 + \frac{3}{2}(0 - t^2)\]

If we operate that, we will finally get:

\[t = \sqrt{ \frac{2 \cdot 0.77778}{3}} = 0.72 seconds\]

Then finally, our total time, this is, the time the car needs to stop moving, will be:

\[T = 18 + 0.72 = 18.72 seconds\]

Hope it's clear and helps :)
 
Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top