Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ziobleed

  1. Z

    what are the differences between CST and Microwave office

    Re: what are the differences between CST and Microwave offic tnx for fast answer , but what is the difference between EM simulator and circuit simulator ?[/youtube]
  2. Z

    what are the differences between CST and Microwave office

    hi all can someone explain me the differences of these two softwares from the point of view of the analysis of circuits ? tnx!
  3. Z

    differences in TOM1 model in libra and AWR ?

    i all i want implement a transitor ( ne32584c a pseudomorfic hemt ) on AWR MWO, but model in datasheet is Libra IV tom model effectly, ive checked the non linear TOM1 model implemented in AWR and they seems the same but when i go to measure the s parameters they differ a lot from that...
  4. Z

    how obtain the same results on AWR MWO and CST

    Hi all Im working on a project of amlifier on AWR microwave office and CST , 1) i designed it on AWR, optimized it 2) i exported the layout on CST via .DXF file and designed the circuit on CST 3) i measure the s parameters of the project on cst but 4) when i put them on MWO again , the...
  5. Z

    how implemet a series IV Libra TOM Model in AWR microwaveoff

    hi all i have a transistor nec NE32584C documentation, the parameters are for series IV Libra TOM Model, but i think that model of fet i using on AWR MWO donesn't match perfectly these parameter i'm using MWO/AO Element Catalog > Nonlinear > FET > TOM1 FET Model: TOM1 there's a way / a guide...
  6. Z

    AWRstudio and CST :How can i implement on CST to obtain same

    Hi all Im working on a project of amlifier on AWR microwave office and CST , 1) i designed it on AWR, optimized it 2) i exported the layout on CST via .DXF file and designed the circuit on CST 3) i measure the s parameters of the project on cst but 4) when i put them on MWO again ...
  7. Z

    Problem with CST low speed when doing a project

    Re: CST very slow tnx for answer so it can be said that the big number of meshes depended by the cad import from microwave office to CST if i design it directly to Cst it will be more fast ? where can i check value of timestep ? bye, however tnx zb
  8. Z

    need help : step by step how measure radiation in CST

    ok thanks a lot zb
  9. Z

    Problem with CST low speed when doing a project

    Re: CST very slow this is a project im working on its very slow on calculation the ports are well set ? and lumpedelements? itwas optimized in microwave office, then exported in CST by a DXF layout file at this point another questionis : what are the settings in CST that simulate at best...
  10. Z

    Problem with CST low speed when doing a project

    i all when i implement an example in CST, it calculatesvery fast and end simulation successfully when i design my own project it takes a lot of more time and somethimes fails ie : abnormally termination i checked all the settings , and, i think, are the same of the examples(similar to my...
  11. Z

    need help : step by step how measure radiation in CST

    hi all I have a design of an UWB amplifier and a patch antenna connected : i want measure the radiation field in CST can you give me a step by step guide to implement this ?
See more

Part and Inventory Search

Back
Top