Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I am currently working in the project which fetches OBD (On Board Diagnostic) information from the cars.
Well, I could read RPM, Speed and other data and ensured that the communication is happening in proper way
But the problem is, I couldn't find any PID for fetching the odometer...
@ Easyrider83 & BradtheRad
Thank you for your kind response
From your answers I came to know that many cars doesn't support VIN number, ok thats really fine
Hence with this I post an other question,
If a car is supporting VIN number, then the PID must be 0902 only or whether it depends upon...
Hello everyone,
I am currently working in a OBD project for automobiles
The proposed device has to fetch certain information from the vehicle
In those basic parameter fetch, VIN (Vehicle Information Number) is the most important
I tried with the request "0902" Mode-9 PID-2 (Intended for VIN)...
Hi all,
We are yet to use Atmel Max touch MXT224E in a project. We would like to stick with MXT224E as we have readymade driver for this controller. Our problem is we could not find anywhere the datasheet for MXT224E. But we have datasheet for MXT224 controller.
Do anybody know the pin...
Hi All,
I am new to Linux Kernel and Can anyone help me where to find a simple linux kernel source code and How to compile and test it in a PC by booting from CD or Pendrive ?..
Can anyone Help with the available tutorials links, etc?.
Thanks in Advance,:-)
Regards,
S.Vigneshwaran
Hi All,
Can anybody help me in developing a code for interfacing a 4.3" TFT through CPU interface to a micro controller.
I want to use 16 bit CPU interface (8080) . Please give me a sample code even if it is "to fill the screen with color " or "to write a line in the TFT" is OK for me.
I am...
Better Select the VHDL designer JOB Profile . There are N number of C programmers where as for VHDL programming Need is high and Programmers is low.
Even though your current job provider Outsource IP from others and allocate the VHDL programmers to integrate the Block, you can take separate...
If that is the case , Is your Board Reading the time from the RTC well ?.
If it is reading and displaying the timings and not accepting the new time , the problem may be related with the Firmware most probably..
let us see after you paste the RTC read code and Time Update code.
Regards...
Hi ..
You are saying that the same configuration of hardware when working with AT89S52
its i working well and its not with P89V51RD2.
Good ..
The issue may be with the code . Let us see your code and the pin assignments you have made for the interface and Tell you where the problem may be ...
top ten embedded coaching center in chennai
Hi All ..
I joined a institute last year for the higher end Embedded Training. .
They gave a very perfect real time training in chennai .
it is in virukambakkam.
Company name is Spectrum Electra Technologies.
They are the only company in...
hot power supply for dspic30f
Dear Alec ,
For 250 ma the heat will be very normal. If it seems abnormal , Check the IO pins that you have connected to the power drivers.
How you had interfaced the IO line with the power driver ?.
Regards,
S.Vigneshwaran.
msp430f1611 4mhz
Hi Infinytus ,
I think this may help if above constraints are there in your circuit .
Connect your codec with the inbuilt SPI of the microcontroller .
Then code the SPI protocol in the firmware and use IO pins as MISO , clk .., etc Pins ...
Transfer your data to the RF...
Hi Ryan ,
You started your profile as a firmware coder due to the project assigned by the company.
Well, Let it be . You study a lot in algorihm calculations as a firware designed.
Tell your higher authorities that you have a interest in VHDL programing.
Often remind them . As a fresher you...
www.electronicsproject.com
Hi Nikitha ,
To have a suggesion about the final year project , kindly specify which department you are doing ?., in which area(Electronics division) you are interested ?..
Then select the project from the list of projects from that area of intertest and DO IT...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.