Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by rocker1025

  1. R

    Operating system and TFT LCD selection for ARM11

    Dear Friends, I want to use Samsung S3C6410 arm 11 for this I want to know Which operating systyem(android version) it will support, Which TFT LCD it will support( maximum size (eg.10.1")) and how to identify these paramters? How to choose the TFT LCD for display? Thanks & Regards Rocker1025
  2. R

    heterogeneous part annotation problem

    Dear Friends, I am using ORCAD 9.1 for entering schematics. I have to make 96 pin euro connector as A,B,C as heterogeneous parts. I made the library as heterogeneous but i am not able to do the annotation it is giving following error i tried so many times pls anyone can solve my problem...
  3. R

    resistor impedance matching

    Hi friends. Please anyone tell me how to calculate for impedance for the attached document. Regards rocker25
  4. R

    Orcad 16.5 dsn to orcad 9.1 version

    Hi friends, I am having Orcad 16.5 capture and Orcad 9.1 Capture two software, i m not able to view orcad 16.5 dsn file in orcad 9.1version. Can anybody give me the solution for this problem. Thanks and Regards rocker25
  5. R

    Designing of 1mA constanta current source

    Thank you sir, Can you tell me how to design constant current source?
  6. R

    Designing of 1mA constanta current source

    Dear Sir, For designing of 1mA,10mA or any current source MOSFET is used why not BJT, can anyone explain me? And also tell me how to design 1mA and 10mA constant current source using PMOSFET?
  7. R

    Opamp power calculation

    Hi, Pls any one tell how to calculate the power consumed by the opamp if i am using +15v and -15v supply also.... i m not able find how to calculate the power consumed by analog mux adg508f with supply vdd = +15V and vss = -15V Thanks & regards Rocker
  8. R

    Current readbak without dividing the current

    Thank u thank u i got it..... thank u very much
  9. R

    Current readbak without dividing the current

    Sir, I have attached my requirement pls check and give me the solution.
  10. R

    Current readbak without dividing the current

    Sir, at the points x and y in the diagram current still divide no....how to solve this?
  11. R

    Current readbak without dividing the current

    can u send me the schematic for how to implement shunt with two buffer amplifier to sense the voltage across it in my block diagram....it is urgent for me sir... ---------- Post added at 11:20 ---------- Previous post was at 11:15 ---------- Sir, actually i have to give 0-20mA to the field...
  12. R

    Current readbak without dividing the current

    Hi Friends, I am having problem with readback of current, actually i m using one VI Converter, output of this VI converter is Iout, this Iout is connected to the output connector and i have to readback this same current to one IV converter without dividing the current, if i took directly...
  13. R

    Highspeed Board Design

    Thank u so much praveen
  14. R

    Highspeed Board Design

    What does mean by high speed board design? Please any explain me about this subject... Thank You rocker1025
See more

Part and Inventory Search

Back
Top