Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by kishor jadhav

  1. K

    3.5MM audio Jack footprint

    Hi all, I am using OrCAD 16.0. I am required 3.5MM audio jack footprint. thanks, Kishor
  2. K

    GSM Module-IShan NAnda

    Hi Ishan, If you are in India so we will give you a best quote for SIM300. If any doubt feel free to ask. We are the bestseller of simcom module.
  3. K

    how to read/write data in 14443a rf tag

    i interface renesas with trf7960 and 14443a tag ' i dont know how to r/w data into tag. i read both trf7960 and tag data sheet but in that also they not given command thanks, ganesh 8087722645 ganeshbadgujar99@yahoo.co.in
  4. K

    OrCAD PCB Editor library file *.dra needed

    OrCAD PCB Editor library Hi, I am just start to work in OrCAD PCB Editor, If anyone know it please mail it's library file(*.dra). Thanks, Kishor
  5. K

    How to add a jumper or link in a board? (OrCAD 16.0)

    Re: How to add a jumper in a board? (OrCAD 16.0) how to add jumper in my board? OR I will directly add to jumper in layout(board) or capture? If it it in capture so how? with best regards, Kishor Jadhav
  6. K

    How to add a jumper or link in a board? (OrCAD 16.0)

    Re: jumper to board I didn't know for how to ask jumper in ORCAD? Added after 6 minutes: Thanks for your replay, I am asking symbl for jumper in layout library with net attachment but it doesn't work or doesn't connect to net & net status was partial routing. Thanks & Regards, Kishor
  7. K

    How to add a jumper or link in a board? (OrCAD 16.0)

    jumper to board Hi all, How to add a jumper or link in a board? I'm using OrCAD 16.0 Thanks in Advance, Kishor
  8. K

    Logo Import from corel to orcad

    Logo Import Dear All, I was Created my Company logo in a corel draw. How to import in OrCAD or it's library? OR How to convert *.cdr file into *.lib? I am using OrCAD 16.0 Thank You, Regards Kishor Jadhav
  9. K

    how to import the cadence 16.0 files to protel

    cadence2protel how to import the cadence 16.0 (scematic, Netlist, pcb file) to Protel( altium 2004) pcb file. please help
  10. K

    How I am load netlist in PCB of altium

    protel (altium) Dear All, I was Draw Schematic in OrCAD 16.0 & imported to Altim 2004 (protel) & generated A NetlistBut How I am load netlist in PCB of altium please help me.
  11. K

    How to change track width

    How to change track width on flying position it means i am started one board to route 1) Vcc Track width is 0.30 Mil & after sometime how i am change track width for another connection. Please help me as soon as possible. I am using OrCAD 16.0 Thanks Kishor Jadhav
  12. K

    Usage of teaching in pcb design

    Re: Teaching of pcb design Thanks Friends your information.
  13. K

    Usage of teaching in pcb design

    Re: Teaching of pcb design sorry friends it's not a teaching, it was a stitching.
  14. K

    sorry it was a stitching of PCB not a teaching

    stitching sorry it was a stitching of PCB not a teaching
  15. K

    Usage of teaching in pcb design

    Teaching of pcb design What is the Teaching? how it is used in PCB design? Thanks & Regards, Kishor Jadhav
See more

Part and Inventory Search

Back
Top