Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi All
I am looking for a cheap solution for pcb screening the component side of my boards. For designing reason I may use two different colours, using the transparencies only gives black. I’ve done a Google search all comes out is using expensive pcb manufacturer machinery.
Searching I came...
Re: Need Help Fixing this Board.. (weirdest thing I've seen
Hi
New IC's are from stock. (same manufacturer)
I applied cold spray to a working unit, it works down to -40C then falls gradually, specs for 0p-amps are -50C max. so I suppose this is OK.
Repeated experiment to my faulty board...
Re: Need Help Fixing this Board.. (weirdest thing I've seen
Freq: 125Hz
* SMD Ceramic Caps
* Using DMM between VCC and Node: No O/P
* Using DMM between Ground and Node: O/P comes on and stays on as long as contact is maintained.
* Using DMM positive lead only: O/P comes on for abut 1...
Re: Need Help Fixing this Board.. (weirdest thing I've seen
As you said banjo applying local heat makes board to work. I have washed tracks with alcohol (IPA) but I can't find any sings of contamination I have also re-soldered all joins but to no bail.
Re: Need Help Fixing this Board.. (weirdest thing I've seen
Hi, banjo Thanks for your input.
I have checked for any cold solder joint o broken tracks under a microscope but this a multilayer board making very difficult fo find if any.
I will try for any leaky capacitor.
thanks again..
Hi All,
I have this faulty board which does not want to operate unless I touch one of the nodes with finger or DMM probe tip. I have many of this boards 100% operating so it is not down to design error. I have measured all component values and all Ok. I have also replaced all Ic's and C392...
CNC PCB Drilling Machine
Has anyone managed to build a home CNC Drilling Machine?
Any building plants to share?
I have read most of the cnc machine posts in the forum and found nothing interesting or easy to follow.
Please share ..
Re: PCB Coating
Oh I see.
no luck there then.
Sorry, I just came across this product.. I want your opinion.
https://www.mgchemicals.com/products/422a.html
Thanks again
PCB Coating
Hi, Guys
I am looking to make profesional looking boards by applying PCB Coating. Does anyone knows where to get the chemicals to accomplish this?
I am after the green stuff on the boards. no plating or Lacquer
any good guides, tutorials out there?
Thanks to all who answer..
Re: PIC SINEWVAE DESIGN
Thanks for your replies XNOX_Rambo an philba..
After so many goes.. I decided to change the DAC08 to AD558 and go an output straight away.. Very HAppy.. -- Now output a bit doted can you suggest any good filter to remove points..
Thanks again..
Re: PIC SINEWVAE DESIGN
As u said XNOX_Rambo the waveform was caused by the inductors, I removed the whole filter section and use the diagram from datasheet but still nada. I get an output form DAC pin 4 of -3.80V even if I disconect the PIC.. is this correct? I'm using +5/-5 to power the...
Re: PIC SINEWVAE DESIGN
Hi pgiatis thanks for answering.
schematic is at the botton of the post. Crystal is 4Mhz.. no load just the scope + a LPF at output.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.