Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by Jepeto

  1. J

    Help me build an SMPS IC

    Re: smps ic selection Linear Application Note 66 power circuits http://www.linear.com/pc/downloadDocument.do?navId=H0,C3,P1164,D4155 TI Reference Design Cookbook Power Management Products http://focus.ti.com/lit/ml/slub009/slub009.pdf Power Management Selection Guide **broken link removed**...
  2. J

    SMD IC and DIP .. componnets ...

    You will pay more for 2 phases soldering process For the next time you can get small quantity SMT components from http://www.digikey.com/ **broken link removed** http://www.mouser.com/ http://www.rs-components.com/index.html
  3. J

    How to check if a bus is available for transmission using CAN code?

    Re: CAN code I think its the MCP2515 job see datasheet page 15 3.3 Initiating Transmission "Note: Setting the TXBnCTRL.TXREQ bit do not initiate a message transmission....transmission will start when the device detects that the bus is available"
  4. J

    Simulate switches for S/H?

    Most of the simulation software has analog switch component All you need is to define the switch parameters Von Voff Ron Roff
  5. J

    what is a digital signal

    ISDN line level of +3v +1v –1v –3v represent the digital signals of 2 bit 00, 01, 10, 11 But its is an analog signal I think signal is digital if it represents only “0” and “1”
  6. J

    What is a digital amplifier and where is it used?

    Re: digital amplifier I guess you are asking about class D amplifier https://www.ee.ucr.edu/~rlake/EE135/Class_D_amp_notes_AL.pdf
  7. J

    Question about buying obsolete parts (BIOS)

    Re: Obsolete part buying The BIOS is standard flash memory IC and the IC manufacturer deliver it empty the chip programmed by the motherboard manufacturer Can you extract the BIOS from the motherboard? If you can, try to get the HEX file and try to program the IC with IC's programmer, maybe...
  8. J

    How to implement a 2x clock multiplier in digital logic?

    clock multiplier xilinx Xlinix application note
  9. J

    Schematic of a 5.1 multichannel amplifier

    Re: schematic see the MPS EVALUATION BOARD EV7720DS-7782-00D 150W class D 5.1 Channel Audio Board **broken link removed** or the Microsemi LXE1722 6-CHANNEL EVALUATION BOARD https://www.microsemi.com/catalog/parmlist.asp?P0_CAT=PM&P1_TYPE=AMAX Instead of building you can buy the evaluation...
  10. J

    Looking for tutorials about OP amp, BJT and MOSFET

    Re: Analog Sites? Op Amps for Everyone Op Amps for Everyone Design Guide from TI **broken link removed** **broken link removed**
  11. J

    How to implement a keypad decoder

    4x4 keypad decoder Simple solution is to wake up the CPU for short time every 1 or 2 seconds with timer interrupt To scan the keys if any key pressed And if not, to send the CPU to sleep
  12. J

    How does a mp3 player work ?

    Re: how do mp3 players work some mp3 projects http://www.pjrc.com/tech/mp3/index.html **broken link removed** **broken link removed** **broken link removed** **broken link removed**
  13. J

    DESIGNING A PULSE OXIMETER TSL230R BASED

    pulse oximeter schematics hope this will help u
  14. J

    Can flash memory be used as a data memory?

    Re: flash memory Yes some micro controllers can do it I know that some of the Microchip 18FXXX family (18fxx2) can write data to the flash program memory on the fly But not all of them
  15. J

    How does CAN BUS work?

    Re: can bus CAN info from kvaser.com https://www.kvaser.com/can/products/index.htm CAN Chips https://www.kvaser.com/can/products/index.htm

Part and Inventory Search

Back
Top