Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by geelani

  1. G

    ADS Help - Equivalent Impedance of S-parameters

    Thanks a lot, i have found it and it works well.
  2. G

    ADS Help - Equivalent Impedance of S-parameters

    Thanks a lot for your help. I opened new schematic and i have one S4P and another S2P (i have made connections), do i need two input ports and how can i measure Zin, can you please help me.
  3. G

    ADS Help - Equivalent Impedance of S-parameters

    Hi All, I need some help regarding ADS simulation, i am a beginner, I have S-parameters of Transmission lines and LNA, i want to make an equivalent impedance of both Tlines+LNA s-parameters which is shown in the picture, please help me how to make this equivalent Impedance.
  4. G

    Converting dBFS/M to dB

    Thanks for the reply
  5. G

    Converting dBFS/M to dB

    Hi, How to convert dBFS/m to dB?. Like my matlab program shows the gain result in dBFS/m:shock: Please help
  6. G

    I need a matlab program to be able to calculate current at any value of pin

    Hi all, Could you please help me in here I need a matlab program to make a formula for the below values: i should be able to calculate current at any value of Pin (say for Pin =0,8) Pin I mA V Pout -11.4 73 3.8 277.4...
  7. G

    Smithchart plot for variable capacitors in ADS

    Thanks a lot, it helps
  8. G

    Smithchart plot for variable capacitors in ADS

    Hi all. I have a question, if this is possible with ADS. I have a simple circuit with 50ohm input impedance and 2 Ohm output impedance. The circuit has two parallel shortstubs connected in series with a capacitor each (Say C1 and C2). Now what i want to do is, putting the constant values of...
  9. G

    Suspended Microstripline BandPassFilter Design : Help

    Hello Abhi, I have registered 6 months ago (Thats how i able to ask help). I cannot download as it says that i have some points to download it..Anyways thank you very much for your kind help. Regards Geelani
  10. G

    Suspended Microstripline BandPassFilter Design : Help

    Hi Abhi Thankyou very much for the suggestion, But i couldnt find the book in this forum, Can you please do let me know the title of the book so that i can search it. Regards Geelani
  11. G

    Suspended Microstripline BandPassFilter Design : Help

    Hello Thank you very much for the information, But do you have any Initial suggestions, Because i am new to Suspended Microstrip line design but not new to Momentum of Analysis. Thanks a lot.
  12. G

    DESIGN OF LOW NOISE AMPLIFIER( HELP ME)

    atf-35143 design For your spec, I would recommend to use SiGE HBT (NPN in CE mode (2 transistors back to back)) in a simple and single ended structure.
  13. G

    Suspended Microstripline BandPassFilter Design : Help

    Hello All, I was told to Design BPF using Suspended Microstripline in the range 925-960MHz in ADS. Can any body help me how to proceed as i am new to this suspended microstripline. By the way i am using ROGERS 4003C substrate. I would highly appreciate for the suggestions. Regards
  14. G

    Gerber Files : Help Regarding

    Thank you very much for the following sites Ramesh it helped me.
  15. G

    Gerber Files : Help Regarding

    pcb_fab_wallchart Hello All, I designed PCB, I converted them into gerber files, I got some mask, err, metric and cond files during conversion. Is there any setting to be done manually in the obtained files. The substrate is ROGERS 4003, But i dont understand which files i have to send to the...
See more

Part and Inventory Search

Back
Top