Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by EngAmira

  1. E

    how to start Sentaurus Device

    you can use this link it will be useful https://web.stanford.edu/class/ee328/swb/swb_a.html
  2. E

    Inspect tool error (sentaurus)

    Hello Everyone I simulate single fin finfet using sentaurus (Synopsys TCAD ), I did structure , sdevice ,sprocess steps but I've problem in inspect tool I try to use CV command to create curves to such formula but I always get an error couldn't create curve " proj_load =...
  3. E

    how to start Sentaurus Device

    please send me ur mail and I will forward to you some manuals for sentaurus tool it can help
  4. E

    sentaurus structure editor (finfet structure error )

    I make multi fin structure on sentaurus structure editor and complete the process and mesh and devise sequence but I always get an error on the structure node which mean that I've errors in my structure but the there is no clear error message to know where the error ??could any one help to...
  5. E

    [Moved:] sentaurus structure editor (finfet structure error )

    I make multi fin structure on sentaurus structure editor and complete the process and mesh and devise sequence but I always get an error on the structure node which mean that I've errors in my structure but the there is no clear error message to know where the error ??could any one help to...
  6. E

    sentaurus preprocess error

    I got some error in sentaurus workbench that some parameters are undefined although I define them on sentaurus workbench and use them with the same names in structure file .can any one help on that ERROR:@L@: undefined variable 'L' at node n16 WARNING: Undefined value for reference L...
  7. E

    Sentaurus preprocess error

    Using sentaurus work bench to create finfet structure I got these preprocessing error for some parameter that are defined in workspace, and used in a structure file as attached photo I don't Know the reason of these attached errors ??
  8. E

    Perl script problem search entry on array on bank system

    I've a aproblem with perl script not executed as required its function is employee bank system which used to add names and salary and title, search certain entry , delete entry ,edit entry the following code show the subrotine for add entry, search entry the add part works properly, but the...
  9. E

    Verilog compile error

    https://www.csee.umbc.edu/portal/help/VHDL/verilog/sequential.html#block this link said that any statement between begin and end executed sequentially (unnamed block ) what do you see??
  10. E

    Verilog compile error

    I thought that if and case statement are sequential statement so statements inside them executed sequentially , am I right ???
  11. E

    Verilog compile error

    ok , so what is the replacement of this enum type in verilog?? - - - Updated - - - so If I need to implement that the elevator door will open for 10 sec then it go close again in sequential manner how could I make it ??
  12. E

    Verilog compile error

    Hello I 've some errors for the below verilog code for elevator control ------------------------------------------------------------------------------------ module elevator_simple(clk,reset,call,requestedFloor, elevatorLocation,moveDown,moveUp,stop,door_state); input...
  13. E

    multifin finfet published IV meaurements

    Hello; Please I need me Id Vd measurement data for (double fin "Nfin=2", and tri fins"Nfin=3") Trigate finfet with gate length =10 nm and 20 nm . how can I search these results thanks Amira
  14. E

    Tcad sentaurus region calling error

    Description: I've a question regarding below structure file command , it is used to define the channel region in multifin finfet as n is number of fins and t is the order of the fin I got error when trying to call the channel region in other file I need to call channel 1, channel 2 and so on...
  15. E

    [Moved]: Sentaurus Tcad (synopsys tool)

    Dear All ; I 'm using sentaurus workbench as attached GUI in simulating multigate mosfet , and I need to add to parameters (number of fins and supply voltage ) as input parameter to the user to sweep on them I added them but can't add the command lines corresponding to those parameter in the...
See more

Part and Inventory Search

Back
Top