Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by campus189

  1. campus189

    Need to measure unknown inductor-Will this meter work ?

    Thanks for reply. I only have regular multimeter I also only have one of these inductors on a pcb :( Got plenty of resistors.
  2. campus189

    Need to measure unknown inductor-Will this meter work ?

    **broken link removed** Will be measuring inductor for a 12v-5 volt car adapter. rated at 1A max. Thanks
  3. campus189

    12 Volts to 3.3 Volts - Help with Chip Selection

    Thanks for the reply. Now you got me thinking :) I got a feeling theat the led's I got are not the best quality, i could be wrong, but i got a great deal on them from flea-bay,, why I bought them. I tried the 120 & 150 Ohm resistors, & got heat as I said. At first I over complicated the issue by...
  4. campus189

    12 Volts to 3.3 Volts - Help with Chip Selection

    Ok, After a lot of tinkering around with using online resistor calculators, I got a lot of wrong values. I did a lot of designs on a bread board & finally achieved my goal. I used Led's that were rated for 3.3 Volts 20mA Max. My goal was to create an emergency light system that ran from...
  5. campus189

    12 Volts to 3.3 Volts - Help with Chip Selection

    **broken link removed** This website is great. Tells all kinds of things about led's
  6. campus189

    12 Volts to 3.3 Volts - Help with Chip Selection

    TY, I'll give it a try :) Would this work? Or should I go with what u said?
  7. campus189

    12 Volts to 3.3 Volts - Help with Chip Selection

    Want to power 24-led's for an emergency lighting project for when the power goes out. Will be running off a 12 Volt deep cell marine battery that is charged by solar panels. Led Specs- 3.2-3.4v 20mA each X 24 =480mA total I am currently using these to go from 12 Volt to 5V. The reason i'm...
  8. campus189

    Nixie clock LC-516 + DCF77

    I like the links to the original content, great for those of us that only know one language and cant figure it out :(
  9. campus189

    Help with 24 led light powered by 12 Volt car battery

    To be more precise , it is .445 Inches or 11.32 mm exactly. Thanks
  10. campus189

    [SOLVED] Would this work? 12 Volt DC Power Inverter to 110v used with Battery Charger?

    Thank You Syncopator Yes, aware that I will still get discharge, but was thinking that the without the charger connected, the battery would discharge a lot faster.. With the charger connected, I will get a slow charge, but was thinking this would extend the discharge time :)
  11. campus189

    [SOLVED] Would this work? 12 Volt DC Power Inverter to 110v used with Battery Charger?

    The battery charger would be plugged into the inverter.the inverter would supply power to the battery charger, which would in turn charge the battery. Even with the battery charger removed from the equation, I can still run CFL'S :) I was just wondering why this would or would not work. The...
  12. campus189

    [SOLVED] Would this work? 12 Volt DC Power Inverter to 110v used with Battery Charger?

    If I were to use these two together with a 12V Car Battery out of the vehicle, do you think this would work ? The Power Inverter connected to the battery & Battery Charger would be plugged into the power inverter & the battery charger connected to the car battery... Basically a loop.. I would...
  13. campus189

    Help with 24 led light powered by 12 Volt car battery

    Yes, I had to put this on hold due to family problems, so. i'm still working on this.. But now I will be posting once again..

Part and Inventory Search

Back
Top