Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
RealAEL Sir,
What is this error unconnected nodes(with only one device attached) and nodes with no DC path to ground. I didn't understand these two errors, how I have to understand these errors and what I have to do for removing these errors
RealAEL Sir,
Now I reduced the step to -50 to +5 , and also introduced "OPTIONS". Also I set the OPTIONS, even though I set introduced options and I am getting the "convergence" problem. How to avoid the convergence problem.
RealAEL Sir,
For my application, I wanted to run Sweep Plan Course to Start =-50 stop= 20 step =5 and Sweep Plan Fine to start = -9 stop =10 step =1. I wanted to get the Sweep Plan course from -50 to +20 . But When I press the Simulation button, it starts to sweep from -50 to -9 ...
Dear husamsdu,
I am surprised, why you are using my post to clear your doubts. Please you can post your own doubt posting and get answer. This is not good way for getting answer from my own postings. You can post new thread and get answer.
RealAEL Sir,
I am searching for the "option component Output tab". But I have searched in the Options > Preferences, couldn't find any component output tab.Where it is option component tab, where I have to go for getting this "option component output tab". There I have to go and...
RealAEL Sir,
As you said , I clicked on the task bar and found the task manager and hpeesofemx.exe, right click on that procsess, and select set Afinity and selected CPU0 or CPU0&CPU1.Then I restarted the ADS and simulated S-parameter momentum. I am getting the same error like as...
RealAEL Sir,
As I told you earlier, I am new for EM simulation in ADS. I request you to check the attached file of BranchLine_Coupler_Zap_File.rar in the posting #1, whether it is in the right form of settings in the ADS or not. If it is not in the correct format, what mistakes I...
Dear Sir,
O.K Sir, I have EM Simulation generated Branch Line Coupler created earlier and attached , made mistake of not setting the "Layout Units" as mm , when schematic I used mm as unit. BigBoss Sir corrected the file and attached in the posting # 3.
What he made the correction...
Dear Sir,
Yes, I have simulated for BigBoss .ZAP modified file, have attached the AWR MWO office file in the posting #4, and ADS file used same as BigBoss modified .ZAP file and simulated the both MWO and ADS file. I am getting results at 3GHz as shown in the posting #4. But I am...
BigBoss Sir,
You told me check the "Layout Units", while translating schematic to layout. Where is the "Layout Units" in ADS2009, where I have to go for getting the "Layout Units" . I searched ,couldn't get "Layout Units". Please where I have to go and search for changing the...
Dear Sir,
For EM simulation , I used Momentum setting up for the substrate and strip conductor declaration and used EMDS for the frequency set up and execution of simulation. I am new to the EM simulation , can you guide me in proper way for EM simulation.
Dear Sir,
I want to generate the Electromagnetic(EM) Simulation for the Branch Line Coupler. I have created the schematic of the Branch line coupler using ADS2009, and generated the layout for the same. Later in the Momentum, I went to substrate > Create/Modify Substrate and went to...
RealAEL Sir,
Thank you for your help, whatever you have shown that link I have gone through. There they have given preventing convergence problems, they said you might have set out range of values, some other reasons also they have given. But they have given in ADS 2011, but I am...
RealAEL Sir,
I have used the template of HB2ToneSweptPwr for my amplifier design measuring IIP3 and OIP3,and am getting following errors. How to resolve this errors for IIP3and OIP3 calculation.Showing error, I have attached below.
RealAEL Sir,
In third order IMD for IIP3 measurement, input power vs output power, I need to convert the rectangular plot to tabular data(Numerical values). How to convert the rectangular plot to tabular data plot ( Numerical values) for IIP3 measurement. Because I need the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
