Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by binu G

  1. binu G

    PMC module template/ info

    Do any one have a layout template for PMC module to share ? Binu G
  2. binu G

    Interfacing two controller

    I have two controller in my design. i plan to use SPI interface between the controllers is there any other method to make the programmer life easy ? Binu G
  3. binu G

    Installing SPB16.3 in mandriva 2010 !

    i happen to install the application successfully. when i run the config i got in to error. . . . . Selecting installed product for configuration ID=PSPT6U DisplayName=SPT6U:Allegro(R) PCB Router 6U - L Version=SPT6U~16.30.000~lnx86 Creating a list of components to configure. NEED...
  4. binu G

    Atmega8 , SMD LQFP, 8Mhz, 3000pcs

    What is the quantity you are looking for ? we have an option to sell in 100 pcs
  5. binu G

    Atmega8 , SMD LQFP, 8Mhz, 3000pcs

    Hi, i have Atmega8 , SMD LQFP, 8Mhz, 3000pcs in stock, if any one interested please contact me at tes.binu@gmail.com
  6. binu G

    Introduction of PCB designers in INDIA

    i work on Conecpt HDL, Allergro, PowerPCB, expedition
  7. binu G

    VB6.0 Developers urgently needed????

    Hello Y.Viswanath are you looking for full time or for a project ? Binu G
  8. binu G

    USB Voice Modem Design

    Hi, i am developing a modem with Voice. which will use the PC Speaker and mike to communicate with this modem. if any one have an experience on this please share Binu G
  9. binu G

    Static Voltage Regulator

    Do any one have experience in protection topology for the switching device used.
  10. binu G

    Static Voltage Regulator

    how do we find if one of the SCR is short ? Binu g
  11. binu G

    Static Voltage Regulator

    Hi, Iam planing to design a static voltage regulator input voltage : 150 to 490V isolated. using ~9 taps SCR drive i need to design a controller which will be able to transfer the tap with out damage or short or two tap on at the same time. please share the experience. Binu G
  12. binu G

    Limiting opamp output to 3.3V

    using a Zener on the signal path degrade the analog voltage supplied to the ADC pin of the controller.
  13. binu G

    Limiting opamp output to 3.3V

    Hi, i have a design with opamp powered at 10 volt but i need to fix the output clamp at 3.3 V. additional circuit should not affect the linearity of the circuit. do any one have a topology to make this working ? Binu G
  14. binu G

    I need to monitor 48V battery, please advise

    well, 48V Vrla battery will have 24 Cells, the customer is interested to know which Cell is damaged. ideally i will need to monitor each cell voltage differentially. how ever i got a flexibility in grouping 6 Cells to form one Zone, so that you will need to monitor 8 Zone, if any of the zone...
  15. binu G

    I need to monitor 48V battery, please advise

    my requiremement is typical, this is for telecom industry and the specification calls for monitoring the battery though the existing controller. the only media between the battery monitoring and controller is a modbus. Binu G
See more

Part and Inventory Search

Back
Top