Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by antaryami.mt.er09

  1. A

    How to simulate a CML Latch or Mux in Cadence

    Hi.... I having a tough problem in simulating the CML circuit, though it is similar to diff amp i don't have idea how to put a logic 1 or logic 0 for a particular swing such that my CML circuit can drive the next stage easily. I mean .... how to put the pulse source during transient simulation...
  2. A

    Some doubts in amplifier.......

    When we talk about the Phase shift of 180 deg in CE amp, it's flow of small signal collector current that flows opposite to the measurement of Output Voltage across load i.e. Beta*Ib flows out of collector terminal, whose direction is opposite to the measurement of our Output voltage, small...
  3. A

    parallel to serial conversion using matlab simulation

    You can try through Parallel in Serial Out Register or MUX based on your desired data rate...
  4. A

    Sequence generator in verilog????

    No idea. I would suggest to get the algo 1st and then write it in C or Matlab , then to verilog .
  5. A

    UMC018 Monte Carlo simulations

    Well i did it with TSMC .18um in Virtuso ADE . U have to select the no of runs , then proces only( which is for unCox , w/l etc) can be thought of as device level, or Mismatch ( is between two identical device with same Vgs , mismatch in current or with identical Ids but mismatch in Vgs) as...
  6. A

    Sequence generator in verilog????

    if you r talking abt PRBS(Pseudo Random Binary Sequence) generator, u should specify how many bits or the length . If u want n- bit PRBS generator ,then it can give u 2^n-1 binary sequences. For PRBS FPGAsRus PRBS which are usually implemented using an LFSR(linear Feedback Shift register) i.e...
  7. A

    Linearity error calculation

    Hi ........ Can anyone please tell me how can i calculate the linearity error from DC characteristic of a Differential amplifier with 2 MOS and a tail current source ?
  8. A

    [SOLVED] how to do dc analysis for this circuit in spectre

    Hi....... For this circuit given below i am trying to do the DC Analysis taking voltages as V1 = V7=Vb+Vin1; V2=V4=Vb+Vin2; V3=V5=Vb+Vin1; and V6=V8=Vb+Vin2 I am taking dc sources for Vb as V0,V1,V2,V3,V4 and another four dc sources as V5,V6,V7,V8 their voltages as Vin1 and Vin2 (respectively...
  9. A

    About ic5141 schematic editor

    go to library manager and right click and hold ,u'll see it is written copy ,then click on that.. now u can change to any library with the a new name of course..........
  10. A

    Vbs of a MOS device during dc analysis in Virtuoso

    hi.. can anyone help me with this... when i run the DC operating point analysis of a circuit in Virtuoso Composer in CADENCE,it shows all the parametrs like Vgs,Vds,Vth,Vdssat but it is not showing the Vbs evenif i am using the input at the bulk . Can u please suggest .....
  11. A

    how to save the schematic to a pdf or .ps file

    how ? i am running my cadence virtuoso in linux.and there is no such option in the virtuoso composer to give ctrl+p... can u please explain...
  12. A

    how to save the schematic to a pdf or .ps file

    Hi......... can anyone help me how to save a schematic in the Virtuoso schematic editor to a diffirent folder where i can use it for doc or pdf
  13. A

    voltage drop across a current source

    i am attaching the image . ---------- Post added at 11:19 ---------- Previous post was at 11:16 ---------- in the diagram i 've shown the mos as a current source .If i replace it with a current source I1 then how can i calculate the voltage drop across it
  14. A

    voltage drop across a current source

    say i have diffirential amplifier and a tail current source of 10mA and vdd=5 v.How can i calculate the voltage drop .After simulation it shows Vsat=some voltage .
  15. A

    voltage drop across a current source

    Hi... can anyone tell me how can calculate the voltage drop across a current source in presence of another components?
See more

Part and Inventory Search

Back
Top