Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by amon

  1. A

    ATCA and Advacned Switch based on PCI-express

    Any clue on how to get the full AS specification?. Thx Amon
  2. A

    Can I use Xilinx JTAG programmer with TI DSPs?

    Re: JTAG That's an excelent suggestion! Xilinx JTAG parallel cable IV is of much lower cost and works well on most motherboards, where the Spectrum Digital parallel cable many times does not work correctly. It may not be difficult to adapt the JTAG plug but question is: how to develop the PP...
  3. A

    Where can I get 10 units of Xilinx XC2VP7-6FF672?

    Xilinx V2Pro FPGA flaw! A few time ago I ordered from Xilinx a few units of XC2VP7-6FF672. Got the chips but a few days after Xilinx reported a flaw in the BGA solder balls, on some chip batches, which emmit alpha particles that may toggle cells programming after at least 300 h of continuous...
  4. A

    The best source code versioning system

    Try: **broken link removed** http://www.tortoisecvs.org/ Amon
  5. A

    Looking for used BGA rework system

    used bga rework system Anyone know where I can look for this equipment, preferably in Europe? With split optics for looking simultaneously to the BGA balls and PCB pad. May include hot-air/IR reflow. Aligning by hand is tricky :) Thanks. Amon
  6. A

    Composite video to VGA schematic request

    video to vga schematic Tnx Taro, I think this circuit will only work for b&w not for color, but its a start :) Amon
  7. A

    How to interface a C64xx DSP to PCI?

    Thanks puckwana, that explains why some PCI boards have a power voltage regulator for obtaining the 3.3V from the 5V lines - those boards are meant to comply with ver. 2.1 of the PCI spec. Another question arises: the signaling voltages of the 5V PCI lines are different from the 3.3 signaling...
  8. A

    How to interface a C64xx DSP to PCI?

    Anyone which can help in this two issues?: - C64xx PCI is 3.3V and standard PC PCI is 5V. - How to design a Linux or Win32 device driver for C64xx PCI. Many thx Amon
  9. A

    Composite video to VGA schematic request

    composite to vga schematic Hi, 1. Most cameras used for PCB inspection have composite video output 2. Everyone has a 14" VGA monitor available 3. The missing link is the schematic of a composite video to VGA Anyone? :) Amon
  10. A

    Xi*linx Development Kit for Vi*rtex II pro

    Thanks buzkiller, I will try Annapolis Microsystems! Amon
  11. A

    Xi*linx Development Kit for Vi*rtex II pro

    Hi, Does anyone know when such kit will be available and from which vendor? Amon
  12. A

    Looking for information on HIPPI

    Hi Bharundi, Look at: CERN HIPPI homepage https://hsi.web.cern.ch/HSI/hippi/ CERN GSN homepage https://hsi.web.cern.ch/HSI/gsn/gsnhome.htm High Speed Interconnect https://hsi.web.cern.ch/HSI/Welcome.html High Performance Networking Forum **broken link removed** Amon
  13. A

    Gigabit Ethernet MAC for Xil*inx

    Hi, Does anyone know if the evaluation of this IP provided in the Xili*nx site, can be used only for simulation or goes all the way up to the PROM stream? Amon
See more

Part and Inventory Search

Back
Top